ShenZhen Yuejiang Technology Dobot Magician Скачать руководство пользователя страница 65

Страница: 65 / 153

Dobot Magician User Guide

Dobot Magician Homing Operation

Issue V1.9.0 (2020-07-23)

User Guide

The Dobot Magician automatically moves above the position (

PenDown

) of the start

point of the text.

Click

Start

to start writing on the paper.

When writing, click

Pause

to pause the writing and

Stop

to halt the writing.

Performing Laser Engraving Tasks

Figure 5.50 shows the process of laser engraving.

Figure 5.50 The process of laser engraving

NOTICE

The LaserEngraving is different is from the grayscale engraving. The former uses the

same firmware and DobotStudio function module as those of the

Write & Draw

function, and it can only engrave a vector graphics by drawing lines while the latter can

engrave a grayscale image. For more information about the grayscale engraving, see

5.6

Engraving a Grayscale Image

Installing a Laser Kit

Procedure

A laser kit includes a laser. For detailed steps, see below.

Содержание Dobot Magician


























































































































































Результаты поиска

Содержание Dobot Magician

Отзывы:

Похожие инструкции для Dobot Magician

Бренды по названию

Популярные бренды

ShenZhen Yuejiang Technology Dobot Magician, Руководство пользователя

Результаты поиска

Содержание Dobot Magician

Отзывы:

Похожие инструкции для Dobot Magician

Бренды по названию

Популярные бренды