SHENZHEN FLYING INDUSTRY DEVELOPMENT CO.,LTD
http://www.carymart.com E-Mail: [email protected]
Press button D of the transmitter or button D of the receiver: The relay 4 is activated, and the equipment 4 is turned on.
Press button D of the transmitter or button D of the receiver again: The relay 4 is deactivated, and the equipment 4 is turned off.
2) Setting Momentary mode: When the receiver is in the learning status, press button B of the transmitter.
Mode Momentary: Press and hold -> On; Release -> Off.
Press and hold button A of the transmitter or button A of the receiver: The relay 1 is activated, and the equipment 1 is turned on.
Release button A of the transmitter or button A of the receiver: The relay 1 is deactivated, and the equipment 1 is turned off.
Press and hold button B of the transmitter or button B of the receiver: The relay 2 is activated, and the equipment 2 is turned on.
Release button B of the transmitter or button B of the receiver: The relay 2 is deactivated, and the equipment 2 is turned off.
Press and hold button C of the transmitter or button C of the receiver: The relay 3 is activated, and the equipment 3 is turned on.
Release button C of the transmitter or button C of the receiver: The relay 3 is deactivated, and the equipment 3 is turned off.
Press and hold button D of the transmitter or button D of the receiver: The relay 4 is activated, and the equipment 4 is turned on.
Release button D of the transmitter or button D of the receiver: The relay 4 is deactivated, and the equipment 4 is turned off.
3) Setting Interlocking mode : When the receiver is in the learning status, press button C of the transmitter.
Mode Interlocking (Channel 1 and 2): Press -> On; Press another button -> Off. Channel 3 and 4 are useless.
Note: This mode is suitable for AC 380V motor forward and reverse rotation (see following circuit diagram 3), and two channels 1 and 2 cannot be
activated at the same time.
Press button A of the transmitter or button A of the receiver: The relay 1 is deactivated, and the 380V motor rotates in the positive direction.
Press button C of the transmitter or button C of the receiver: The relay 1 is deactivated, and the 380V motor stops.
Press button B of the transmitter or button B of the receiver: The relay 2 is activated, and the 380V motor rotates in the reversal direction.
Press button D of the transmitter or button D of the receiver: The relay 2 is deactivated, and the 380V motor stops.
4) Setting Self-l Interlocking mode: When the receiver is in the learning status, press button D of the transmitter.
Mode Self-locking (Channel 1) + Mode Interlocking (Channel 2 and 3), Channel 4 is useless.
Note: This mode is suitable for AC 380V motor forward and reverse rotation (see following circuit diagram 4), and two channels 2 and 3 cannot be
activated at the same time.
Press button A of the transmitter or button A of the receiver: The relay 1 is activated, and the power of 380V motor is turned on.
Press button A of the transmitter or button A of the receiver again: The relay 1 is deactivated, and the power of 380V motor is turned off.
Press button B of the transmitter or button B of the receiver: The relay 2 is deactivated, and the 380V motor rotates in the positive direction.
Press button D of the transmitter or button D of the receiver: The relay 2 is deactivated, and the 380V motor stops.
Press button C of the transmitter or button C of the receiver: The relay 3 is activated, and the 380V motor rotates in the reversal direction.
Press button D of the transmitter or button D of the receiver: The relay 3 is deactivated, and the 380V motor stops.
Manual button "Stop" of the receiver:
In any case, pressing this manual button will deactivate all relays.
How to pair the transmitter to the receiver:
1) Press the setting button of the receiver for 5~6 seconds until signal LED on the receiver flashes 3 times, then release the setting button. The
receiver enters into the learning status.
2) Press any button on transmitter within 5 seconds, if signal LED flashes 5 times then turns off, it means learning is successful.
3) The receiver can learn several transmitters with different codes.
Delete all transmitters:
We have learned the
transmitter to the receiver. If you don’t want the receiver to work with the transmitter, you can delete all codes of the transmitters
which are stored in the receiver.
Operation: Pressing the setting buttons of the receiver for 10~12 seconds until the signal LED on the receiver flashes 5 times, then release the
setting button. This means all stored codes have been deleted successfully.
