background image

 

  

 

     SADP_Operating_ Instructions_0114 

      

 

 

 

2.1   Hazardous Area Use – Safety 

 

   

All SADP Shaw Automatic Dewpoint meters are certified Intrinsically Safe as a standard feature.  

   

They must be fully assembled to meet the certification requirements, i.e. they must not be switched on 
in a hazardous location if any component is missing or removed. E.G. battery cover plate or sensor 
head assembly etc.  This instrument is only certified Intrinsically Safe to T6 with the use of Varta 3014 
long life batteries as supplied. 

 

 

Certification: 

ATEX Coding -    

      

II 1G 

 

   

 

Ex ia IIC T6 Ga (Ta =  – 20ºC to +40ºC) 

 

FM Coding - CLASS I, ZONE 0 AEx ia IIB+H2 T6 

 

   

 

 

 

 

 

 

 

 

 

 

It is the responsibility of the user to ascertain the suitability of the SADP for use in hazardous areas. 
Risk assessments should be performed prior to use, taking into account the SADP certifications, the 
location and the gas being monitored etc.   

 
   

The USA certification is to CLASS I, ZONE 0 AEx ia IIB+H2 T6, which effectively means that the 
instruments may be used in any environment except a deep mine. 

 
   

The ATEX certification is Ex II 1 G Ex ia IIC T6 Ga.  This means:- 

 
   

Ex-European certification mark for electrical equipment for use explosive atmospheres 

   

II   -Areas classified hazardous due to presence of flammable gases or vapour  

   

1   -Areas classified as Category 1 Risk according to the ATEX Directive (equates to Zone 0) 

   

G  -Risk due to presence of flammable gases or vapours according to the ATEX Directive 

   

Ex ia - Intrinsic Safe 

   

IIC - suitable for use with all classes of gasses and vapours  

   

T6 - the product has a maximum surface temperature of 85°C (in an ambient temperature range of -
20°C to + 40°C) and can be used with any gases or vapours which have an ignition temperature above 
this.  

 

Ga  - EPL (Equipment Protection Level) marking 

 

2.2 Pressure Exposure 

 

 

The maximum pressure to which the telescopic measuring head is exposed 

must not be more than 

 

0.3barg, 4.35psig, 30kpag or 0.3kg/cm

2

 

Exposing the measuring head to higher pressures may damage the instrument 

and result in injury to the operator or other personnel in the area 

 

 

 
 
 
 

Содержание SADP






















Отзывы: