Sharp XV-Z1A Скачать руководство пользователя страница 33

Страница: 33 / 65

TROUBLE SHOOTING TABLE

(Continued)

XV-Z1E/A

Checking the G signal line of output PWB

Yes

Connector CC poorly soldered or in
trouble.

Are outputs at pins (3), (4) and (5) of
IC4034 as specified?

Are there signal inputs at pins (1)
each of IC4038 thru IC4043?

Check connector CC. Do signals go
to pins (4), (5), (7), (8), (10) and (11)
of this connector?

IC4034, IC5002 or nearby circuit in
trouble.

Yes

Are there signal outputs at pins (7),
(8) and (14) of IC4044 and IC4045?

IC4038 thru IC4043, IC4044, IC4045
or nearby circuit in trouble.

Yes

Are signals fed from pins (2) thru (7)
of connector GP to the panel?

Connector GP poorly soldered or in
trouble.

Yes

Does flicker happen?

Go to "Checking the image for
shifting".

Yes

Is frame pulse fed to pin (1) of
connector GP?

Yes

Is common bias at pin (24) of
connector GP as specified?

Yes

Panel in trouble.

Yes

Q4024, Q4025, Q4026 or their signal
line in trouble.

Does frame pulse go out of IC4077?

Yes

Are FRP1 and FRP2 signals fed to
pins (9) and (12) of IC4077?

Any of IC4038 thru IC4043 faulty.

Checking the image for shifting

Yes

IC1001 or nearby circuit in trouble.

Are signals fed via IC4074, IC4075
and IC4076 to the panel?

Panel in trouble.

Are signals fed to IC4074, IC4075
and IC4076?

IC4074, IC4075, IC4076 or nearby
circuit in trouble.

IC4077 or nearby
circuit in trouble.

IC1001 or nearby
circuit in trouble.

Содержание XV-Z1A


































































Результаты поиска

Содержание XV-Z1A

Отзывы:

Похожие инструкции для XV-Z1A

Бренды по названию

Популярные бренды

Sharp XV-Z1A, Руководство по обслуживанию

Результаты поиска

Содержание XV-Z1A

Отзывы:

Похожие инструкции для XV-Z1A

Бренды по названию

Популярные бренды