Sharp XL-HF401PH, Руководство по эксплуатации

Страница: 17 / 37

12/3/17 HF401PH_OM_EN.fm
10
9
8
7
6
5
4
3
2
1
E-6
General control
Press the ON/STAND-BY button to turn the power on.
To dim the display brightness, press the DEMO/DIMMER
button on the remote control.
If you turn off and on the main unit with the volume set to 27 or
higher, the volume starts at 16 and fades in to the last set level.
Turn the volume knob towards /– (on main unit) or press
VOL +/– (on remote control) to increase or decrease the volume.
When you press any of the following buttons, the unit turns on.
●
iPod, CD, USB, AUDIO/LINE INPUT, TUNER, NETWORK on the
remote control: Selected function is activated.
●
/ button on the main unit: The unit turns on and playback of the last func-
tion will start (CD, TUNER, USB, iPod, AUDIO IN, LINE IN, NETWORK)
During stand-by mode, when you select XL-HF401PH speaker
through AirPlay icon on your AirPlay device, the unit will
automatically power on to Network function and stream the
music from your AirPlay device.
This condition applies when:
●
The AirPlay network has previously been set up
between the unit and your AirPlay device.
●
Set the Network Stand-by mode to ON. (refer page 9)
During other function (CD, TUNER, USB, iPod, Audio In, Line In), when you select XL-
HF401PH speaker through AirPlay icon on your AirPlay device, the unit will
automatically switch to Network function and stream the music from your AirPlay
device.
This condition applies when:
●
The AirPlay network has previously been set up
between the unit and your AirPlay device.
The main unit will enter the stand-by mode (when iPod, iPhone
or iPad is not connected) after 15 minutes of inactivity during:
iPod:
Not docked.
Audio In: No detection of input signal.
CD:
In the stop mode or no disc.
USB: In the stop mode or no media.
Note:
However, if iPod or iPhone is docked, the unit will begin
charging. “Charge Mode” will be displayed.
The volume is muted temporarily when pressing the (MUTE)
button on the remote control. Press again to restore the volume.
When the power is first turned on, the unit will enter the extra
bass mode which emphasises the bass frequencies, and
“X-Bass On” will appear. To cancel the extra bass mode, press
the X-BASS button on the remote control.
When the FUNCTION button on main unit is pressed, the
current function will change to different mode. Press the
FUNCTION button repeatedly to select desired function.
Note:
The backup function will protect the memorised function mode
for a few hours should there be a power failure or the AC power
lead becomes disconnected.
Setting the clock (Remote control only)
In this example, the clock is set for the 24-hour (0:00) display.
■
To turn the power on
After use:
Press the ON/STAND-BY button to enter the power stand-by mode.
■
Display brightness control
■
Volume auto fade-in
■
Volume control
■
Direct key power on function
■
Auto power on
■
AirPlay auto switch
■
Auto power off function
CD/USB
RDS
Dimmer 1
Dimmer 2
Dimmer Off
(Display is dim).
(Display is bright).
(Display gets dimmer).
■
Muting
■
X-Bass control
■
Bass control
1
Press the BASS/TREBLE
button to select “Bass”.
2
Within 5 seconds, press
the VOLUME (+ or –)
button to adjust the bass.
■
Treble control
1
Press the BASS/TREBLE
button to select “Treble”.
2
Within 5 seconds, press
the VOLUME (+ or –)
button to adjust the treble.
■
Function
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CLOCK/TIMER button.
3
Within 10 seconds, press the ENTER button. To adjust the
day, press the
or button and then press the
ENTER button.
4
Press the or button to select 24-hour or 12-hour
display and then press the ENTER button.
The 24-hour display will appear.
(0:00 - 23:59)
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
- 5 ↔ - 4........ ↔ + 4 ↔ + 5
- 5 ↔ - 4........ ↔ + 4 ↔ + 5
FM S TEREO FM MONO
iPod A u dio In
Line In
U S B
CD
Network
CD/USB
RDS