background image

INSTALLATION INSTRUCTIONS

               

                  

CEILING BRACKET AN-PHCM20 

INSTALLATION INSTRUCTIONS

               

                  

CEILING BRACKET AN-PHCM20 

PAGE 11 

ONE YEAR LIMITED WARRANTY 

 

SHARP Electronics Corporation warrants to the first end use purchaser, that this SHARP brand 
product (the “Product”), when shipped in its original container, will be free from defective  
workmanship and materials, and agrees that it will, at its option, either repair the defect or replace 
the defective product or part thereof at no charge to the purchaser for parts or for labor, excluding 
costs of removal and/or installation, for one year from date of purchase. 
 
This warranty does not apply to any appearance items of the Product nor to any Product the  
exterior of which has been damaged or defaced, which has been subject to misuse, abnormal  
service or handling, or which has been altered or modified in design or construction. 
 
In order to avail the purchaser of his/her rights under this limited warranty, the purchaser should 
carry in or ship the Product prepaid and insured, including proof of purchase, to:   
SHARP Electronics, c/o AVDEX, 115 Henry Street, Freeport, NY 11520. 
 
The limited warranty described above is in addition to whatever implied warranties may be 
granted to purchasers by law.  To the extent permitted by applicable law ALL IMPLIED  
WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR 
USE ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH 
ABOVE.  Some states do not allow limitations on how long an implied warranty lasts, so the 
above limitation may not apply to you. 
 
Neither the sales personnel of the seller nor any other person is authorized to make any  
warranties other than those described above, or to extend the duration of any warranties beyond 
the  time period described above on behalf of SHARP. 
 
The warranties described above shall be the sole and exclusive warranties granted by SHARP 
and shall be the sole and exclusive remedy available to the purchaser.  Correction of defects, in 
the manner and for the period of time described herein, shall constitute fulfillment of all liabilities 
and responsibilities of SHARP to the purchaser with respect to the Product, and shall constitute 
full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise.   
In no event shall SHARP be liable, or in any way responsible, for any damages or defects in the 
Product which were caused by repairs or attempted repairs performed by anyone other than 
SHARP.  Nor shall SHARP be liable or in any way responsible for incidental or consequential  
economic or property damage.  Some states do not allow the exclusion of incidental or  
consequential damages, so the above exclusion may not apply to you. 
 
THE WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS.  YOU MAY ALSO HAVE OTHER 
RIGHTS WHICH VARY FROM STATE TO STATE. 
 
Specifications are subject to change without notice.   
 

SHARP ELECTRONICS CORPORATION, SHARP PLAZA, MAHWAH, NJ 07430 

Содержание XG-PH50X - XGA DLP Projector














Отзывы: