Sharp vc-ga56z Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 74

background image

47

VC-GA56Z

VC-GH96Z

Linear audio playback is impossible. (Hi-Fi E-E mode is normal).

Are MH-AA harness and playback AMP. peripheral parts normal?

Is the AC head surface clean?

Is AC head height adjusted properly?

Replace the AC head.

Readjust the A/C head height.

Is audio signal output to the pin(11) of IC201?

YES

YES

YES

YES

YES

YES

NO

NO

NO

NO

Is it possible to confirm the audio signal (PB EQ)
on pin(100) of IC201?

Replace IC201.

Is pin(99) of IC201 in "L" level?

Check the line between pin(11) of IC201and
pin(62) of IC651.

FLOW CHART NO.27

Check the periphery of pin(99) of IC201. (R617)

«
...
45
46
47
48
49
...
»

Содержание vc-ga56z











































































Отзывы:

Нет отзывов

Похожие инструкции для vc-ga56z

Бренд: CCTV Imports Страницы: 74

Бренд: Lilin Страницы: 34

Бренд: 247Security Страницы: 53

Бренд: Okina Страницы: 59

Бренд: Speco Страницы: 93

Бренд: dallmeier Страницы: 147

Бренд: Lenovo Страницы: 164

Бренд: Lenovo Страницы: 5

Бренд: AUSTAR Страницы: 78

Бренд: Speco Страницы: 19

Бренд: Speco Страницы: 77

Бренд: Speco Страницы: 114

Бренд: SVA Страницы: 1

Бренд: Surveon Страницы: 4

Бренд: Chipatronic Страницы: 16

Бренд: Safestmonster Страницы: 3

DS-7208HWI-SV DS-7216HWI-SV

Бренд: HIKVISION Страницы: 264

DS-7208/16HWI-SV

Бренд: HIKVISION Страницы: 261

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды