Sharp UX-P110 Скачать руководство пользователя

Страница: 31 / 84

Sending a Fax by Normal Dialling

2. Sendi

•

If the other party answers, ask them to press their Start key (if you pressed

, pick up the handset to speak with them). This causes the receiving

machine to issue a fax tone.

When you hear the fax tone, press

. Replace the handset.

•

If the transmission is completed successfully, the fax will beep once.

•

If an error occurs, the fax will beep three times and print a Transaction
Report to inform you of the problem (see page 64).

START/MEMORY

Note:
If the transmission is unsuccessful and DOCUMENT JAMMED appears in the
display, remove the document as explained on page 77. (This may occur if the

other fax machine doesn’t respond properly when you attempt to send the
document.)

all.book

Page 29

Monday, August 19, 2002

4:05 PM

Содержание UX-P110





















































































Результаты поиска

Содержание UX-P110

Отзывы:

Похожие инструкции для UX-P110

Бренды по названию

Популярные бренды

Sharp UX-P110, Руководство по эксплуатации

Результаты поиска

Содержание UX-P110

Отзывы:

Похожие инструкции для UX-P110

Бренды по названию

Популярные бренды