R-953/963M - 23
(1) Structure of Absolute Humidity Sensor
The absolute humidity sensor includes two thermistors
as shown in the illustration. One thermistor is housed
in the closed vessel filled with dry air while another in
the open vessel. Each sensor is provided with the
protective cover made of metal mesh to be protected
from the external airflow.
(2) Operational Principle of Absolute Humidity Sensor
The figure below shows the basic structure of an
absolute humidity sensor. A bridge circuit is formed by
two thermistors and two resistors (R1 and R2).
The output of the bridge circuit is to be amplified by the
operational amplifier.
Each thermistor is supplied with a current to keep it
heated at about 150˚C, the resultant heat is dissipated
in the air and if the two thermistors are placed in
different humidity conditions they show different de-
grees of heat conductivity leading to a potential differ-
ence between them causing an output voltage from the
bridge circuit, the intensity of which is increased as the
absolute humidity of the air increases. Since the output
is very minute, it is amplified by the operational ampli-
fier.
(3) Detector Circuit of Absolute Humidity Sensor Cir-
cuit
This detector circuit is used to detect the output voltage
of the absolute humidity circuit to allow the LSI to
control sensor cooking of the unit. When the unit is set
in the sensor cooking mode, 16 seconds clearing cycle
occurs than the detector circuit starts to function and
the LSI observes the initial voltage available at its AN1
terminal.
With this voltage given, the switches SW1 to SW5 in
the LSI are turned on in such a way as to change the
resistance values in parallel with R97 ~ R102. Chang-
ing the resistance values results in that there is the
same potential at both F-3 terminal of the absolute
humidity sensor and AN0 terminal of the LSI. The
voltage of AN1 terminal will indicate about -2.5V. This
initial balancing is set up about 16 seconds after the
unit is put in the Sensor Cooking mode. As the sensor
cooking proceeds, the food is heated to generate
moisture by which the resistance balance of the bridge
circuit is deviated to increase the voltage available at
AN1 terminal of the LSI.
Then the LSI observes that voltage at AN1 terminal and
compares it with its initial value, and when the compari-
son rate reaches the preset value (fixed for each menu
to be cooked), the LSI causes the unit to stop sensor
cooking; thereafter, the unit goes in the next operation
automatically.
When the LSI starts to detect the initial voltage at AN1
terminal 16 seconds after the unit has been put in the
Sensor Cooking mode, if it is not possible to balance
the bridge circuit to disconnection of the absolute
humidity sensor, ERROR will appear on the display
and the cooking is stopped.
1) Absolute humidity sensor circuit
ABSOLUTE HUMIDITY SENSOR CIRCUIT
Sensing part
(Open vessel)
Sensing part
(Closed vessel)
C
S
R3
R1
R2
+
Operational
amplifier
Output
voltage
S : Thermistor
open vessel
C : Thermistor
closed vessel
2
Absolute humidity (g/m )
Output voltage
Absolute humidity vs,
output voltage characteristic
SW1
SW2
SW3
SW4
SW5
P54
P53
P52
P51
P50
LSI
(IC1)
AN0
AN1
620k
300k
150k
75k
37.4k
13
16
17
1
5
8
7
4
6
80
15
14
47k
47k
IC2
10k
0.01uF
0.015uF
0.01uF
+
VA : -15V
VA : -15V
R90
C90
C91
C93
C92
S
F-2
1.8k
F-1
F-3
C
3.57k
3.32k
VC : -5V
0.1 uF
C. Thermistor in
closed vessel
S. Thermistor in
open vessel
R98
R99
R96
R91
360k
R93
R92
R94
R95
R100
R101
R102
R97
