Sharp R-7H55 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 44

background image

31

R-7H55

2. Deviation of door alignment from horizontal line of cavity

face plate is to be less than 1.0mm.

3. Door is positioned with its face pressed toward cavity

face plate.

4. Re-install outer case and check for microwave leakage

around door with an approved microwave survey meter.
(Refer to Microwave Measurement Procedure.)

Note:

The door on a microwave oven is designed to act as
an electronic seal preventing the leakage of
microwave energy from oven cavity during cook
cycle. This function does not require that door be air-
tight, moisture (condensation)-tight or light-tight.
Therefore, occasional appearance of moisture, light
or sensing of gentle warm air movement around
oven door is not abnormal and do not of themselves,
indicate a leakage of microwave energy from oven
cavity.

UPPER DOOR
HINGE PIN

SCREWS

UPPER
OVEN HINGE

SCREWS

LOWER DOOR HINGE PIN

LOWER
OVEN HINGE

Figure C-4. Door Replacement and adjustment

DOOR DISASSEMBLY

Remove door assembly, refer to "Door Replacement".
Replacement of door components are as follows:
1. Place door assembly on a soft cloth with latches facing

up.

Note: As the engaging part of choke cover and door panel

are provided at 22 places, do not force any particular
part.

2. Insert an putty knife (thickness of about 0.5mm) into the

gap between the choke cover and corner portion of door
panel as shown Figure C-5 to free engaging parts.

3. Lift up choke cover.
4. Now choke cover is free from door panel.
5. Remove six (6) screws holding the door frame to the

gutter for choke cover.

6. Remove the door frame with pulling the upper door

hinge pin.

Figure A-1

CUT

H.V. READ WIRES

H.V. RECTIFIER

ASYMMETRIC RECTIFIER

PROCEDURE FOR SERVICE OF DEFECTIVE HV. RECTIFIER ASSEMBLY

1. When a part of the HV. Rectifier was defect, please replace the whole HV.

Rectifier assembly.

2. When a part of the Asymmetric Rectifier was defect, please remove part of

it by cut lead wires as shown Fig. A-1.

2-1. After remove it, please check operation of the unit. If no power,

please replace main fuse.

2-2. Put water load in the oven and operate the unit. If no heat, please

replace the magnetron.

∆

Please keep more than 15.5mm of clearance distance from left of
leads to other parts.

Blown fuse due to defective asymmetric rectifier

There are many cases that the fuse is blown due to defective asymmetric rectifier. So, please follows below.

SERVICE INFORMATION

1. When use the current HV. Rectifier assembly with the Asymmetric Rectifier for service, please remove a part of the

Asymmetric Rectifier by cut lead as shown in Figure A-1.

2. When the HV. Rectifier assembly with the Asymmetric Rectifier in the microwave oven was defect, please take steps

indicated in below

Figure C-5. Door Disassembly

DOOR
PANEL

CHOKE
COVER

«
...
31
32
33
34
35
...
»

Содержание R-7H55













































Отзывы:

Нет отзывов

Похожие инструкции для R-7H55

Бренд: Zanussi Страницы: 26

Бренд: Zanussi Страницы: 17

Бренд: Zanussi Страницы: 18

Бренд: Zanussi Страницы: 20

Бренд: Zanussi Страницы: 20

Бренд: Zanussi Страницы: 24

Бренд: Zanussi Страницы: 20

Бренд: Zanussi Страницы: 24

Бренд: Zanussi Страницы: 24

Бренд: Zanussi Страницы: 3

Cuisinair FBI 783 W

Бренд: Zanussi Страницы: 24

Бренд: Zanussi Страницы: 19

Бренд: Zanussi Страницы: 20

Бренд: Zanussi Страницы: 24

B1ACC2A 0 Series

Бренд: NEFF Страницы: 28

Бренд: Oster Страницы: 17

Бренд: Euro-Pro Страницы: 49

Бренд: Cafe Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды