background image

R-408DW
R - 410DK
R-410DW

In the interest of user-safety the oven should be restored to its original
condition and only parts identical to those specified should be used.

WARNING TO SERVICE PERSONNEL: Microwave ovens con-
tain circuitry capable of producing very high voltage and
current, contact with following parts may result in a severe,
possibly fatal, electrical shock. (High Voltage Capacitor, High
Voltage Power Transformer, Magnetron, High Voltage Recti-
fier Assembly,  High Voltage Harness etc..)

TABLE OF CONTENTS

Page

PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO
AVOID POSSIBLE  EXPOSURE TO EXCESSIVE MICROWAVE ENERGY .................. INSIDE FRONT COVER
BEFORE SERVICING ..................................................................................................... INSIDE FRONT COVER
WARNING TO SERVICE PERSONNEL .............................................................................................................. 1
MICROWAVE MEASUREMENT PROCEDURE .................................................................................................. 2
FOREWORD AND WARNING ............................................................................................................................. 3
PRODUCT SPECIFICATIONS ............................................................................................................................. 4
GENERAL  INFORMATION ................................................................................................................................. 4
OPERATION ........................................................................................................................................................ 6
TROUBLESHOOTING GUIDE ............................................................................................................................. 9
TEST PROCEDURE ........................................................................................................................................... 10
TOUCH CONTROL PANEL ................................................................................................................................ 18
COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE ................................................................ 22
PICTORIAL DIAGRAM ....................................................................................................................................... 28
POWER UNIT CIRCUIT ...................................................................................................................................... 29
CPU UNIT CIRCUIT ............................................................................................................................................ 30
PRINTED WIRING BOARD ................................................................................................................................ 31
PARTS LIST ........................................................................................................................................................ 32
PACKING AND ACCESSORIES ......................................................................................................................... 36

S30M142R410DE

R-408DW
R-410DK
R-410DW

MICROWAVE OVEN

MODELS

    SERVICE MANUAL

R-410DW

MINUTE PLUS

POPCORN

BEVERAGE

COMPU DEFROST

POWER

LEVEL

TIMER
CLOCK

INSTANT ACTION

1

2

3

4

5

6

7

8

0

9

TO ADJUST QUANTITY - TOUCH PAD AGAIN

1 2 0 0   W A T T S

DINER

PLATE

CASSEROLE

1 GROUND MEAT
2 STEAKS/CHOPS
3 CHICKEN PIECES

BAKED

POTATOES

FRESH

VEGETABLES

GROUND

  MEAT

FROZEN

ENTREES

FROZEN

VEGETABLES

M ICROWAVE

PIZZA

ROLLS&

MUFFINS

STOP

CLEAR

START

DEFOST

DEFOST

COOK

COOK

NO.

NO.

LBS.

LBS.

CUPS.

CUPS.

OZ.

OZ.

SHARP ELECTRONCS CORPORATION

This document has been published to be used for after
sales service only.
The contents are subject to change without notice.

Service Headquarters: Sharp Plaza, Mahwah, New Jersey, 07430-2135

Содержание R-408DW











































Отзывы: