Sharp R-370EK Скачать руководство пользователя страница 31

Страница: 31 / 44

R-370EK
R-370ES

1. Disconnect the power supply cord, and then remove

outer case.

2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Push the lever of positive lock

connector.

5. Pull down on the positive lock

connector.

CAUTION: WHEN CONNECTING THE POSITIVE LOCK

CONNECTORS TO THE TERMINALS, CON-
NECT THE POSITIVE LOCK

SO THAT THE

LEVER FACES YOU

POSITIVE LOCK

CONNECTOR (NO-CASE TYPE) REMOVAL

1. Disconnect the power supply cord.
2. Remove turntable and turntable support from oven cavity.
3. Lay the oven on it's backside. Remove the turntable

motor cover by snipping off the material in four corners.

4. Where the corners have been snipped off bend corner

areas flat.

TURNTABLE MOTOR REMOVAL

5. Disconnect wire leads from turntable motor.

(See "Positive lock connector removal")

6. Remove two (2) screws holding turntable motor to oven

cavity.

7. Remove the TTM packing from the turntable motor

shaft.

Terminal

Push

Pull down

Lever

Positive lock®

connector

fan blade.

5. Install the fan blade to the shaft of fan motor by pushing

the fan blade with a small, light weight, ball peen hammer
or rubber mallet.

CAUTION:
*

Do not hit the fan blade strongly when installed
because the bracket may be disfigured.

Make sure that the fan blade rotates smooth after
installation.

Make sure that the axis of the shaft is not slanted.

6. Catch two holes of fan duct on two tabs of the base plate.

7. Hold the fan duct assembly to the base plate with the two

(2) screws.

8. Re-install the separete angles A, B and C to the base

plate with each one (1) screw.

9. Insert the main wire harness and switch harness into the

holes of the fan duct.

10.Connect the wire leads to the fan motor. Referre to

"PICTORIAL DIAGRAM".

11.Re-install the oven cavity assembly to the base plate.

Refere to "OVEN CAVITY ASSEMBLY REMOVAL".

12.Reconnect all wire leads removed from components.

Referre to "PICTORIAL DIAGRAM".

Gap

Rotor

Bracket

Stator

Groove joint pliers

Coil

Shaft

Axis

Stator

Rotor

These are the positions
that should be pinched
with pliers.

Shaft

Table

Center of
bracket

Side View

Rear View

POWER UNIT REMOVAL

1. Disconnect the power supply cord and remove outer

case.

2. Open the door and back it open.
3. To discharge the high voltage capacitor, waite for 60

seconds.

4. Disconnect the wire leads and the connectors from the

power unit.

5. Remove two (2) screws holding power unit to the base

plate.

6. With needle nose pliers, nip and push the head of the

one (1) PC support clip which holds the power unit. And

then release the clip from the hole of the power unit.

7. Now the power unit is free.

Figure C-2. PC support clip

Needle nose pliers

Power unit

PC support clip

Figure C-3. Positive lock

connector

Содержание R-370EK













































Результаты поиска

Содержание R-370EK

Отзывы:

Похожие инструкции для R-370EK

Бренды по названию

Популярные бренды

Sharp R-370EK, Руководство по обслуживанию

Результаты поиска

Содержание R-370EK

Отзывы:

Похожие инструкции для R-370EK

Бренды по названию

Популярные бренды