Sharp R-20A1SVN Скачать руководство пользователя страница 15

Страница: 15 / 28

R-20A1(S)VN

10 – 2

[3] HIGH VOLTAGE TRANSFORMER REMOVAL

1. CARRY OUT 3D CHECKS.

2. Disconnect the wire leads (main wire harness and H.V. fuse) from

high voltage transformer.

magnetron.

high voltage capacitor.

5. Remove the two (2) screws holding the transformer to bottom plate

from below.

6. Remove the two (2) screws holding the transformer to bottom plate

from above.

7. Remove the transformer.

[4] HIGH VOLTAGE RECTIFIER ASSEMBLY, HIGH VOLTAGE FUSE AND HIGH VOLTAGE
CAPACITOR REMOVAL

To remove the components, proceed as follows.

1. CARRY OUT 3D CHECKS.

2. Disconnect the H.V. fuse from the high voltage transformer.

magnetron.

the H.V. capacitor.

5. Remove one (1) screw holding capacitor holder to the oven cavity

back plate.

6. Remove one (1) screw holding earth side terminal of high voltage

assembly from high voltage capacitor.

8. Disconnect the H.V. fuse from the high voltage capacitor.

free.

CAUTION: WHEN REPLACING HIGH VOLTAGE RECTIFIER

ASSEMBLY, ENSURE THAT THE CATHODE (EARTH)
CONNECTION IS SECURELY FIXED TO THE CAPACI-
TOR HOLDER WITH AN EARTHING SCREW.

CAUTION: DO NOT REPLACE ONLY HIGH VOLTAGE RECTIFIER.

WHEN REPLACING IT, REPLACE HIGH VOLTAGE REC-
TIFIER ASSEMBLY.

[5] MAGNETRON REMOVAL

1. REMOVAL

1. CARRY OUT 3D CHECKS.

2. Disconnect the wire leads from the magnetron.

3. Remove the two (2) screws holding the air duct to the oven cavity.

4. Release the air duct from the oven cavity.

5. Carefully remove the four (4) screws holding the magnetron to the

6. Lift up magnetron with care so that the magnetron antenna is not

hit by any metal object around antenna.

7. Now, the magnetron is free.

2. REINSTALLATION

screws.

2. Reinstall the air duct to the oven cavity with the two (2) screws.

3. Reconnect the wire leads to the magnetron. Refer to “PICTORIAL

DIAGRAM”.

4. Reinstall the outer case and check that the oven is operating prop-

erly.

CAUTION: WHEN REPLACING THE MAGNETRON, BE SURE THE

R.F. GASKET IS IN PLACE AND THE MAGNETRON
MOUNTING SCREWS ARE TIGHTENED SECURELY.

[6] POSITIVE LOCK CONNECTOR (NO-CASE TYPE) REMOVAL

1. CARRY OUT 3D CHECKS.

2. Push the lever of positive lock connector.

3. Pull down on the positive lock connector.

CAUTION: WHEN CONNECTING THE POSITIVE LOCK CONNEC-

TORS TO THE TERMINALS, CONNECT THE POSITIVE
LOCK

SO THAT THE LEVER FACES YOU.

Figure C-1. Positive lock

connector

Terminal

Push

Pull down

Lever

Positive lock¨

connector

Содержание R-20A1SVN





























Результаты поиска

Содержание R-20A1SVN

Отзывы:

Похожие инструкции для R-20A1SVN

Бренды по названию

Популярные бренды

Sharp R-20A1SVN, Руководство по обслуживанию

Результаты поиска

Содержание R-20A1SVN

Отзывы:

Похожие инструкции для R-20A1SVN

Бренды по названию

Популярные бренды