background image

5

R-203BW
R-209BK
R-220BW

Electrical Requirements
The electrical requirements are a 115 -120 volt 60 Hz, AC only,
15 or 20 amp. fused electrical supply. It is recommended that a separate
circuit serving only this appliance be provided. When installing this
appliance, observe all applicable codes and ordinances.
A short power-supply cord is provided to reduce risks of becoming
entangled in or tripping  over a longer cord.
Where a two-pronged wall-receptacle is encountered, it is the personal
responsibility and obligation of the customer to contact a qualified
electrician and have it replaced with a properly grounded three-pronged
wall receptacle or have a grounding adapter properly grounded and
polarized. If the extension cord must be used, it should be a 3-wire, 15
amp. or higher rated cord. Do not drape over a countertop or table where
it can be pulled on by children or tripped over accidentally.

3-Pronged Plug

Grounded
Receptacle Box

Grounding Pin

3-Pronged Receptacle

OVEN DIAGRAM

1. Oven door with see-through window
2. Safety door latches.
3. Door hinges
4. Door seals and sealing surfaces
5. Turntable motor shaft
6. Removable turntable support
7. Removable turntable
8. Ventilation openings. (Rear)
9. Oven lamp.
10. Wave guide cover.
11. Power supply cord

TOUCH  CONTROL PANEL

CAUTION: DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE ROUND GROUNDING PRONG FROM

THIS PLUG.

R-203BW

R-209BW

R-220BW

DEF.

LBS.

QTY. CHECK

ON

Time display

Indicator

1  

2  

3  

4  

5  

6  

7  

8  

0  

9  

DEFROST

EXPRESS

MINUTE

PLUS

SNACKS

COOKING

REHEATING

POPCORN

BEVERAGE

BAKED

FRESH

POTATO

VEGETABLES

DINNER

PLATE

ROLL,

MUFFIN

DEFROST

EXPRESS

MINUTE

PLUS

SNACKS

COOKING

REHEATING

POPCORN

BEVERAGE

BAKED

FRESH

POTATO

VEGETABLES

DINNER

PLATE

ROLL,

MUFFIN

1  

2  

3  

4  

5  

6  

7  

8  

0  

9  

DEFROST

EXPRESS

MINUTE

PLUS

SNACKS

COOKING

REHEATING

POPCORN

BEVERAGE

BAKED

FRESH

POTATO

VEGETABLES

DINNER

PLATE

ROLL,

MUFFIN

8

10

11

9

1

2

5

7

3

4

6

Содержание R-203BW









































Отзывы: