background image

E-6

Specifications

SHARP reserves the right to make design and specification changes for product improvement
without prior notice.

Cleaning the tape-handling
parts

Dirty heads, capstan or pinch roller can cause
poor sound and tape jams. Clean these parts
with a cotton swab moistened with commer-
cial head/pinch roller cleaner or isopropyl al-
cohol.

After long use, the deck’s heads and cap-
stan may become magnetised, causing poor
sound. Demagnetise these parts once eve-
ry 30 hours of playing/recording by using a
commercial tape head demagnetiser. Read
the demagnetiser’s instructions carefully be-
fore use.

Cleaning the cabinet

Periodically wipe the cabinet with a soft cloth
and a diluted soap solution, then wipe with a
dry cloth.

Caution:

Do not use chemicals for cleaning (petrol,
paint thinner, etc.). It may damage the cabi-
net finish.

Do not apply oil to the inside of the unit. It
may cause malfunctions.

■ 

Condensation

Sudden temperature changes, storage or op-
eration in an extremely humid environment may
cause condensation inside the cabinet (tape
heads, etc.).
Condensation can cause the unit to malfunc-
tion.
If this happens, leave the power on with no
cassette in the unit until normal playback is
possible (about 1 hour).

Maintenance

AC 110-127/220-240 V, 50/60 Hz
DC 6 V [“D” size (UM/SUM-1, R20 or HP-2) battery x 4]
7 W
MPO: 3 W (AC operation, 10 % T.H.D.)
RMS: 1.5 W (DC operation, 10 % T.H.D.)
9.2 cm (3-5/8”) full range speaker x 1
Earphone: 16-50 ohms (recommended: 32 ohms)
Width: 305 mm (12”)
Height: 155 mm (6-1/8”)
Depth: 120 mm (4-3/4”)
1.48 kg (3.3 lbs.) without batteries

General

Power source

Power consumption
Output power

Speaker
Output terminal
Dimensions

Weight

FM: 88 - 108 MHz
SW1: 2.3 - 7.3 MHz
SW2: 7.3 - 22 MHz
MW: 526.5 - 1,606.5 kHz

Radio

Frequency range

Tape recorder

Frequency response

Signal/noise ratio

Wow and flutter

Motor

Bias system

Erase system

60 - 12,000 Hz (Normal tape)

40 dB

0.3 % (WRMS)

DC 6 V electric governor

DC bias

Magnet erase

QT-222W(B)  92L20101550040

QT-222W(B)_E.pm

03.10.24, 11:55 AM

13

Содержание QT-222W











Отзывы: