Sharp PG-C45X - Notevision XGA LCD Projector Скачать руководство пользователя страница 88 | Manualshive

Страница: 88 / 107

background image

Appendix

-83

Maintenance Indicators

■

The warning lights on the projector indicate problems inside the projector.

■

If a problem occurs, either the temperature warning indicator or the lamp replacement indicator will
illuminate red, and the power will turn off. After the power has been turned off, follow the proce-
dures given below.

Temperature warning

indicator

Lamp replacement

indicator

Power indicator

About the temperature warning indicator

If the temperature inside the pro-
jector increases, due to blockage
of the air vents, or the setting lo-
cation, “

” will blink in the

lower left corner of the picture. If
the temperature keeps on rising,
the lamp will turn off and the tem-
perature warning indicator will
blink, the cooling fan will run for
further 90 seconds, then the power
will be shut off. After “

” ap-

pears, be sure to perform the fol-
lowing measures.

About the lamp
replacement indicator

■

The lamp life becomes 0%, when used

for approximately 2,000 hours with “ON”
in “Power Save” or when used for approxi-
mately 1,500 hours with “OFF” in “Power
Save” (see page

■

When the remaining lamp life becomes

6% or less, “

” will be displayed on the

screen in yellow. When the percentage
becomes 0%, “

” will change to “

”

(red), the lamp will automatically turn off
and then the projector as well. At this time,
the lamp replacement indicator will illu-
minate

in red.

■

If you try to turn on the projector a fourth

time without replacing the lamp, the pro-
jector will not turn on.

Maintenance indicator

Condition

Problem

Possible Solution

Temperature

warning

indicator

Normal

Abnormal

Off

Red on/
Power off

The internal
temperature is
abnormally high.

Abnormal

•

Blocked air intake

•

Relocate the projector to an area
with proper ventilation.

•

Cooling fan break-
down

•

Internal circuit failure

•

Clogged air intake

•

Take the projector to your nearest
Sharp Authorized Projector Dealer
or Service Center (see page

)

for repair.

Lamp

replacement

indicator

Red on/
Power off

The lamp does
not illuminate.

•

Burnt-out lamp

•

Lamp circuit failure

•

Carefully replace the lamp. (See
page

•

Take the projector to your nearest
Sharp Authorized Projector Dealer
or Service Center (see page

for repair.

•

Please exercise care when
replacing the lamp.

Green on

Green

blinks

when the

lamp is

active.

Red blinks/
Red on

Time to change
the lamp

•

Remaining lamp life
becomes 6% or
under.

Power

indicator

The power
indicator blinks
in red when the
projector is on.

•

The filter cover, lamp
unit cover or lens
cover is open.

•

Securely install the covers.

•

If the power indicator blinks even
when the filter cover is securely
installed, contact your nearest
Sharp Authorized Projector Dealer
or Service Center for advice.

Green on/
Red on

Red blinks

«
...
86
87
88
89
90
...
»

Содержание PG-C45X - Notevision XGA LCD Projector












































































































Отзывы:

Нет отзывов

Похожие инструкции для PG-C45X - Notevision XGA LCD Projector

Бренд: AAXA Technologies Страницы: 2

Event Master E2

Бренд: Barco Страницы: 2

Бренд: Barco Страницы: 7

Бренд: Avermedia Страницы: 58

Бренд: AAXA Technologies Страницы: 49

Бренд: Yaber Страницы: 101

Бренд: Sinew Страницы: 44

Бренд: Remaco Страницы: 2

Бренд: Epson Страницы: 24

ELP-5500 - PowerLite 5500C SVGA LCD Projector

Бренд: Epson Страницы: 2

EMP 30 - PowerLite 50c XGA LCD Projector

Бренд: Epson Страницы: 2

Бренд: Epson Страницы: 4

Бренд: Epson Страницы: 32

Бренд: Epson Страницы: 4

Бренд: Epson Страницы: 3

Бренд: Epson Страницы: 75

Бренд: Epson Страницы: 1

Бренд: Epson Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды