Sharp MX-M550 Скачать руководство пользователя страница 60

Страница: 60 / 200

MISFEED REMOVAL

2-30

■

Misfeed in the tray 5 (AR-LC7)

If a paper misfeed occurs, follow the steps below to remove the misfeed.

Open the side cover.

Remove the misfed paper.

Be careful not to tear
the misfed paper
during removal.

Gently close the side cover.

Close the bypass tray.

Open the top cover of the AR-LC7 (tray 5).

Hold the top cover
open.

Remove the misfed paper.

Be careful not to tear
the misfed paper
during removal.

After removing the
misfed paper, close the
top cover.

Pull out tray 1 - tray 2.

Grasp the finger hold
and gently open the
tray.

Pull the tray all the way
out until it stops.

Remove the misfed paper.

Check the paper
transfer unit inside the
tray. If there is a
misfeed in the paper
transfer unit, remove
the misfeed.

Gently push tray 1-tray 2 into the machine.

Push the tray firmly all
the way into the
machine.

Make sure that the
misfeed message no
longer appears (the
normal message
display should appear).

NOTE

If a misfeed occurs in the following situation, push tray
1 - tray 2 back in and then pull the tray out again:

●

A misfeed occurs during printing from tray 5 (AR-
LC7) while paper is being loaded in tray 1 - tray 2.

dragonII_copy_sec.book 30 ページ２００６年１０月１８日　水曜日　午後７時３９分

Содержание MX-M550









































































































































































































Результаты поиска

Содержание MX-M550

Отзывы:

Sharp MX-M550, Руководство по эксплуатации, Страница: 60 / 200

Результаты поиска

Содержание MX-M550

Отзывы: