Connecting your set
4 First time installation
Introduction
When the set fi rst turns on, it enters the First Time Installation
mode. This can be restarted by restoring the set to default settings
in the ‘About TV’ Menu.
Country Selection
Select the correct fl ag for the country in which the set will be
used in. This will enable the set to correctly install the functions
applicable in the country of use.
Environment of Use
Home Mode:
For normal use, by default it is set to a power saving mode
which reduces the energy used by up to 25% (by reducing the power to
the LED/LCD panel). This can be changed in the picture mode settings.
Network setup
You can connect the TV to your broadband router or wireless network in order
to take advantage of the Smart functions. If you connect the TV to your router
using an Ethernet cable (recommended) this step will be skipped.
Set Up Netfl ix
If you have a Netfl ix account, it can be set up on the television
here. Once set up and validated, the First Time Installation
returns to the next step.
Default Source
Select the source which you use the most. If Digital TV (Freeview) is chosen,
then at the next step, the set will tune in and default to Digital TV (Freeview).
If one of the other sources is selected, then the set will not tune in at this
stage and default to that input. If it is required to tune the set in later, press
the [MENU] button and then select Settings>Channels
Tune in Channels
Choose to install terrestrial channels now or later.
Support Advice
Information regarding support is displayed for a little while.
Tuning continues and a progress bar is shown with the number of
channels found indicated below.
If you are picking up signals from more than one transmitter, you
will be requested to select your primary and secondary regions.
1
2
3
4
5
6
7
8
9
Basic installation steps are shown below. These may vary slightly depending on model.
Note:
In home mode,
the TV will switch off
automatically after 4
hours in the event that
no buttons are pressed on
the TV or remote control.
(You can change this
by pressing the [MENU]
button and then selecting
Settings>Time>Auto
Standby)
Languages
Select your preferred on-screen display language. This will change the language
in which the menus and associated information is displayed in. When set up has
been completed, to change this press the [MENU] button and then select Settings >
System Menu > Language
HDMI input 2.0
R
L
Ethernet/LAN*
Network
connection
Digital Audio
Digital Optical Audio Output
USB 1
USB port 2.0
USB 2
USB port 2.0
L/R
HDMI input
HDMI 1
HDMI input 2.0
Video/YPbPr
SAT IN Satellite input
RF in RF / TV aerial input
HDMI 3 HDMI input 2.0 (ARC)
USB 3 USB port 2.0
CI card in Common interface module
SD SD card input
Earphones Earphone input
Service Input
Setting up the TV set for the fi rst time
Connectivity
1) Connect the TV to your power socket.
2) If you wish to use the TV to receive Freeview/Saorview channels, connect the RF input from
the TV to your outdoor Digital TV aerial. If you do not wish to receive Freeview/Saorview, skip
this step.
2
To receive Freeview channels, in particular
Freeview HD channels, you will need a
Digital TV aerial and be in a good Freeview
coverage area. You can check coverage for
your postcode at www.freeview.co.uk.
Please note that any Freeview HD channels
found during tuning will be placed in
channel positions above 100.
For example, 101 (BBC1 HD) 102 (BBC2 HD)
etc.
Outdoor Digital
TV Aerial
1.
2.
Used for attaching the stand
to the TV set (fi g.2)
6 x
* The Ethernet/LAN port is used for Freeview HD services and smart functions.
Place the TV set on a fl at and clean surface
with the panel facing downwards to avoid
damage.
When the two feet are fi tted, they will appear
as in the picture above, with the tips of the feet
pointing away from each other.
When the stand/feet are in the correct position,
secure the feet to the underside of the TV set
using 6 screws provided.
EA
R
P
H
O
N
E
SA
T I
N
US
B
3(
2.0
)
900mA
MAX
ARC
K
N
O
3
Powering On the TV
Switch on the television by pressing the TV control stick
located on the TV set.
TV control stick
Insert the batteries supplied into the remote control and
press the standby button to power on the TV.
TV Control Stick
Remote Control:
Installing Batteries
Terms and conditions apply. Online registration only.
Register your manufacturers
guarantee online within
14 days of purchase at
www.registertoday.co.uk/sharp
and enter into a prize draw to
win a Sharp Soundbar
A
H
L
K
B
I
M
C
D
E
F
G
J
1 (2.0)
2 (2.0)
ETHERNET
DIGITAL
AUDIO OUT
OPTICAL
L
R
VIDEO/Y
Pb
Pr
5V
500mA MAX
USB 1 (2.0)
5V
500mA MAX
USB 2 (2.0)
A
B
C
D
E
F
G
I
J
L
M
P
1 x
Operating Instructions
1 x Quick Start Guide
1 x TV
1 x Stand installation pack
1 x Remote Control
1 x
RF Cable
2 x AAA Batteries
Fitting the stand
1
1
2
6 x
3
TV panel must be facing downwards.
What is included
in the box
Note:
To complete the stand
installation you will require a
cross head screw driver.
UK Only.
ROI Only.
To receive Saorview channels, in particular
Saorview HD channels, you will need a
Digital TV aerial and be in a good Saorview
coverage area. You can fi nd out more at
www.saorview.com.
Video Input (green) and HD input
(Ypbpr)
HDMI 2
Audio shared for Video/Composite
and component/ YPbPr
H
P
O
Input is used only by
service centres
N
SHA-QSW-0041 LC-70UI9362K.indd 2
SHA-QSW-0041 LC-70UI9362K.indd 2
16/11/2018 13:58:17
16/11/2018 13:58:17
