manualshive.com logo in svg

Sharp LC-40LE810E, Руководство по обслуживанию

Поделиться
Скачать
Sharp LC-40LE810E Скачать руководство пользователя страница 5

LC-40/46LE810E, LC-40/46LX810E

iv

LC-40LE810E

Service Manual

 

OUTLINE

MAJOR SERVICE PARTS

„

PWB UNIT

NOTE: (*1) Replace MAIN Unit (DKEYDF455FM03) in case of IC8401 or IC3302 failure.

(*2) TOUCH SENSOR Unit (RUNTKA692WJQZ) reuse will be impossible, once it is stuck on front cabinet and exfoliates.

       Therefore, please exchange of a TOUCH SENSOR Unit in the case of front cabinet exchange.

„

OTHER UNIT

„

IC FOR EXCLUSIVE USE OF THE SERVICE

„

SERVICE JIGS

Ref No.

Parts Code

Description

N

DKEYDF455FM03

MAIN Unit (*1)

N

DUNTKF494FM02

R/C, LED Unit

N

DUNTKF493FM03

ICON Unit

N

RUNTKA692WJQZ

TOUCH SENSOR Unit (*2)

N

RUNTKA685WJQZ

POWER Unit (LC-40LE810E/LX810E)

N

RUNTKA686WJQZ

POWER Unit (LC-46LE810E/LX810E)

N

RUNTK4512TPZC

LCD CONTROL Unit (LC-40LE810E/LX810E)

N

RUNTK4437TPZE

LCD CONTROL Unit (LC-46LE810E/LX810E)

N

RUNTK4462TPZZ

LED PWB Unit, x4 (LC-40LE810E/LX810E)

N

RUNTK4461TPZZ

LED PWB Unit, x4 (LC-46LE810E/LX810E)

Ref No.

Parts Code

Description

N

R1LK400D3LWF2Y

40” LCD Panel Module Unit (LC-40LE810E/LX810E)

N

R1LK460D3LWA2Y

46” LCD Panel Module Unit (LC-46LE810E/LX810E)

Ref No.

Parts Code

Description

Q’ty

IC501

RH-iXD108WJQZS

IC  24LC21AT-I/SN

1

IC2002

RH-iXC786WJNJQ

IC  R5F364A6NFB

1

Ref No.

Parts Code

Description

Q’ty

N

QCNW-G616WJQZ

Main Unit to LCD Control Unit (LW)

1

N

QCNW-G625WJQZ

Main Unit to Power Unit (PL) 

1

N

QCNW-H184WJQZ

Main Unit to Power Unit (PD)

1

N

QCNW-H185WJQZ

Main Unit to Power (LED Drive) Unit (LB)

1

N

QCNW-K594WJQZ

Main Unit to R/C, LED Unit (RA)

1

N

QCNW-K595WJQZ

Main Unit to Speaker (SP)

1

N

QCNW-K597WJQZ

Main Unit to Woofer (SB)

1

Содержание LC-40LE810E




















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды