ELECTRICAL ADJUSTMENTS
D-1
1. ADJUSTMENT PROCEDURE
Read and perform these adjustments when repairing the
circuits or replacing electrical parts or PCB assemblies.
On-Screen Display Adjustment
1.
2.
Set the VOLUME to minimum.
Press the VOL. DOWN button on the set and the
channel button (9) on the remote control for more than
2 seconds to display adjustment mode on the screen as
shown in Fig. 1-1.
3.
4.
5.
Use the Channel UP/DOWN button or Channel button
(0-9) on the remote control to select the options shown
in Fig. 1-2.
Press the INPUT button on the remote control to end
the adjustments.
To display the adjustment screen for TV, AV, AV(S),
YUV and HDMI mode, press the INPUT button on the
remote control to set to the TV, AV, AV(S) YUV and
HDMI mode. Press the VOL.DOWN button on the set
and the channel (9) on the remote control for more than
2 seconds.
FUNCTION
H POSI OSD
V POSI OSD
R DRIVE(N)
R CUT OFF(N)
G DRIVE(N)
G CUT OFF(N)
B DRIVE(N)
B CUT OFF(N)
R DRIVE(C)
R CUT OFF(C)
G DRIVE(C)
G CUT OFF(C)
B DRIVE(C)
B CUT OFF(C)
R DRIVE(W)
R CUT OFF(W)
G DRIVE(W)
G CUT OFF(W)
B DRIVE(W)
B CUT OFF(W)
H POSI 50Hz
NO.
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
FUNCTION
H POSI 60Hz
V POSI 50Hz
V POSI 60Hz
BAK LIGHT CENT
BAK LIGHT MAX
BAK LIGHT MIN
BRIGHT CENT
BRIGHT MAX
BRIGHT MIN
TINT
CONTRAST CENTER
CONTRAST MAX
CONTRAST MIN
COLOR CENT
COLOR MAX
COLOR MIN
CONTRAST 40
BRIGHT (3F54)
CONTRAST(3F55)
SRC TOP
DFEA VIMGVT
Fig. 1-2
Function
Step No.
Fig. 1-1
01 H POSI OSD 346
TV
NO.
22
23
24
25
26
27
28
29
30
31
35
36
37
38
39
40
43
44
45
46
47
CAUTION
ï
ï
ï
Use an isolation transformer when performing any
service on this chassis.
When removing a PCB or related component, after
unfastening or changing a wire, be sure to put the wire
back in its original position.
When you exchange IC and Transistor with a heat sink,
apply silicon grease (YG6260M) on the contact section
of the heat sink. Before applying new silicon grease,
remove all the old silicon grease. (Old grease may cause
damages to the IC and Transistor).
Prepare the following measurement tools for electrical
adjustments.
1. Pattern Generator
2. BASIC ADJUSTMENTS
2-1: CONTRAST MAX
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
Receive the monoscope pattern. (RF Input)
Using the remote control, set the brightness and contrast to
normal position.
Activate the adjustment mode display of Fig. 1-1 and press
the channel button (36) on the remote control to select
"CONTRAST MAX".
Press the LEFT/RIGTH button on the remote control until
the contrast step No. becomes "219"
Check if the picture is normal.
Receive the monoscope pattern. (VIDEO Input)
Press the INPUT button on the remote control to set to the
AV mode.
Using the remote control, set the brightness and contrast to
normal position.
Activate the adjustment mode display of Fig. 2-1 and press
the channel button (36) on the remote control to select
"CONTRAST MAX".
Press the LEFT/RIGTH button on the remote control until
the contrast step No. becomes "217".
Check if the picture is normal.
Playback the DVD(480i) disc. (COMPONENT Input)
Press the INPUT button on the remote control to set to the
YUV mode.
Using the remote control, set the brightness and contrast
to normal position.
Activate the adjustment mode display of Fig. 2-1 and
press the channel button (36) on the remote control to
select "CONTRAST MAX".
Press the LEFT/RIGTH button on the remote control until
the contrast step No. becomes "199".
Playback the DVD(480i) disc. (HDMI Input)
Press the INPUT button on the remote control to set to the
HDMI mode.
Using the remote control, set the brightness and contrast
to normal position.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (36) on the remote control to
select "CONTRAST MAX".
Press the LEFT/RIGTH button on the remote control until
the contrast step No. becomes "168".
Check if the picture is normal.
