Sharp JH-3500U Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 33

Sharp JH-3500U Скачать руководство пользователя страница 18

15

Connecting to DC Disconnect

This section describes the connection between the solar power conditioner and the DC disconnect. The distribution of the
connection are the output cables from the PV string (maximum three pairs of cables) and a grounding cable from the DC
disconnect.

Follow all WARNING and CAUTION of Wiring Solar Power Conditioner (page 13).

G

GND terminal

DC terminal Block for
DC disconnect

1.

Utilize

AWG12 cables for DC input single copper conductor wire (positive and negative) from the

DC disconnect through the conduit. Up to three pairs can be connected to the solar power
conditioner. Each pair should be marked as one pair of cables which are connected to the same
PV string when installing the PV array.

Tape

Tape

2.

Locate

the grounding cable

(

AWG 10 single copper conductor wire

)

from the DC disconnect

enclosure. This cable should be also located in the same conduit pipe used for the DC cables.

3. Remove the jacket of only one of the positive cables (black) which is connected to the first

terminal block. The length of the exposed conductor should be long enough to connect to the
DC terminal securely, and

short enough

to avoid touching any part except the terminal. See

below for detail.

16mm±1mm

DC cable

13mm±1mm

grounding cable

4.

Connect

the cable to the positive terminal of the terminal block 1 (rightmost), and tighten the screw

firmly to crimp the cable.

+

-

«
...
16
17
18
19
20
...
»

Содержание JH-3500U


































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды