Sharp FO-4450, Руководство по обслуживанию, Страница: 19 / 170

FO-4450U/FO-CS1
M) All FAX/TEL. entry mode
This is a function to copy the FAX and TEL numbers registered in the
one-touch dialing (RAPID) key [01] to the all one-touch dialing (RAPID)
key and the all abbreviated number (SPEED DIAL) to simplify the FAX
and TEL number registration at the time of aging.
1
Copy the Fax and Tel numbers (including agency) registered in the
one-touch dialing (RAPID) key [01] to all one-touch dialing (RAPID)
key.
2
Copy the FAX and TEL numbers registered in the one-touch dialing
(RAPID) key [01] to the all abbreviated number (SPEED DIAL).
3
In case the chain dial is not set in the one-touch dialing (RAPID) key
[01], register the one-touch dialing (dialing) keys [02] – [59] and all
abbreviated number (SPEED DIAL) to the group number [01].
In case that the chain dial is set, do not create a group, but cancel
only the chain dial setting of the one-touch dialing (RAPID) key [01].
(All except for the one-touch dialing (RAPID) key [01], chain dial is
kept set.)
4
Enter all registered one-touch send (RAPID) keys and speed dial
numbers (SPEED DIAL) on the personal books [01] - [10].
Following this, set the password registration and the password
setting to ON, and set the TTI setting to OFF.
The call-receiver names and book names are specified as follows:
(The letters after 16th letter of the call-receiver’s name registered in the
one-touch dialing [01] are cut off.)
NOTE: Before entering this mode, FAX and TEL numbers must be reg-
istered in the one-touch dialing (RAPID) key [01].
(In case that they are not registered, or a program or a group is
registered, it is not executed.)
N) Dept. passcode
The department passcode list is printed.
O) Conf. passcode
The confidential passcode list is printed.
Differing from printing of one box alone soon after registration, the con-
fidential passcodes of all boxes are printed.
P) Signal send mode 2
The signals concerned with V.34 & V.8 are checked.
After this mode is activated, press the START key, and the signals will
be sent in the following sequence.
It can be used to check the modem.
[ 1] No signal
[ 2] 33600BPS (V. 34)
[ 3] 31200BPS (V. 34)
[ 4] 28800BPS (V. 34)
[ 5] 26400BPS (V. 34)
[ 6] 24000BPS (V. 34)
[ 7] 21600BPS (V. 34)
[ 8] 19200BPS (V. 34)
[ 9] 16800BPS (V. 34)
[10] 14400BPS (V. 34)
[11] 12000BPS (V. 34)
[12] 9600BPS (V. 34)
[13] 7200BPS (V. 34)
[14] 4800BPS (V. 34)
[15] 2400BPS (V. 34)
[16] 0 - 300BPS (V. 34)
[17] ANSam
Q) Memory set mode
The set and dump list of the memory content is output.
•
The address (8 digits (P) generally including the bank information is
input, and the data of 2 digits is continuously input.
Inputting is done in the hexadecimal mode. The ten-key is used for 0
through 9, and the alphabetic keys A (RAPID 01 through 06) are
used for A through F.
•
During data inputting, the address can be moved forward and back-
ward one byte by one byte with " " and "#". (The address prior to the
address 0 is looped as the maximum address.)
•
The Validity of the address is not checked. Accordingly, writing/ read-
ing operations are possible in the address of the memory not as-
signed, the address of ROM and so on.
(However, as practical, writing is not done, and the data content runs
short each reading.)
Though writing is possible in the flash memory, a little time is re-
quired.
It is also necessary to take care that the life of the flash memory is
excessively shortened if much data is written in the flash memory.
Since it may run away depending the written content, take minute
care for the writing address.
•
When the REPORT key is input, the memory dump list is produced
from the displayed address (here, it is limited at the 16-byte bound-
ary address (address with end 0) which does not exceed the speci-
fied address and is just in front.). The dump list is output to a maxi-
mum of 99 pages. If any data of one page can be repeatedly devel-
oped and printed, the list is sufficient. But it is not desired that the
content of plural pages are developed in the memory once and are
then printed. If the STOP key is pressed, it will pass to the diagnosis
after the page which is now being printed is completed printed.
If the address exceeds the maximum address, it will return to the
address 0 and printing will be continued.
R) Stamp aging mode
This is a mode to execute the continuous drive aging of the Verification
stamp.
1
Set the document and press down the “START” key and the
continuous drive of the Verification stamp starts.
2
Send the document at the interval of 10 mm and stamp the
Verification stamp continuously. The total number of times of
Verification stamp printing after entering this mode is displayed on
the display.
•
Displayed screen during execution
3
By pressing down the “STOP” key during the action, or when no more
document is left, the continuous drive of the Verification stamp stops.
NOTE:
•
In case that the document is not set, this cannot be executed.
•
The normal action aging that one Verification stamp is pressed on one
sheet of document is executed in the normal copying.
Rapid R XX XX : Rapid key send
SPEED DIAL S XXX XXX : Speed dial number
Personal book BOOK XX XX : Book number
2 – 5
MEMORY SET MODE
AD = 00000000
Cursor
MEMORY SET MODE
AD = A02800F6 DATA = 0B
STAMP AGING
TIMES = 13 PAGES = 1
Print total number
of times Page number