Sharp FO-165, Руководство по обслуживанию, Страница: 32 / 112

SW-A6 No. 2 End buzzer
Setting this bit to 0 will disable the end buzzer (including the error
buzzer/on-hook buzzer).
SW-A6 No. 3 Disconnect the line when DIS is received in RX
mode
Bit1= 0: When DIS signal is received during RX mode, disconnect the
line immediately.
Bit1= 1: When DIS signal is received during RX mode, wait the next
signal.
SW-A6 No. 4 Equalization freeze control
This switch is used to perform reception operation by fixing the equal-
izer control of modem for the line which is always in unfavorable state
and picture cannot be received.
* Usually, the control is executed according to the state of line where
the equalizer setting is changed always.
SW-A6 No. 5 Equalization freeze 7200 bps only
Setting which specifies SW-A3 No. 6 control only in condition of 7200
bps modem speed.
SW-A6 No. 6 ~ No. 8 Reserved
Set to "0".
SW-B1 No. 1 ~ No. 4 Recall interval
Choice is made for a redial interval for speed and rapid dial calls.
Used a binary number to program this. If set to "0" accidentally, 1 will
be assumed.
SW-B1 No. 5 ~ No. 8 Recall times
Choice is made as to how many redials should be.
SW-B2 No. 1 ~ No. 8 Reserved
Set to "0".
SW-B3 No. 1, No. 2 PBX recall function (R key select)
Used to set the operation mode of PBX recall when the R key is
pressed.
Setting is mode according to the type of PBX.
No. 1 = 1, No. 2 = 1: Time break recall (=Flash) is performed.
The DPON on the LIU board is driven to initiate
recall.
No. 1 = 1, No. 2 = 0: Earth recall is performed.
The E-relay on the LIU board is driven to initiate
recall.
SW-B3 No. 3 ~ No. 5 Reserved
Set to "0".
SW-B3 No. 6 Mercury line
0: No
1: Yes
Default: 0
SW-B3 No. 7 ~ No. 8 Reserved
Set to "0".
SW-B4 No. 1, No. 2 Reserved
Set to "0".
SW-B4 No. 3 Dial mode
When using the pulse dial, set to "0". When using the tone dial, set to
"1".
SW-B4 No. 4 key Pulse dial
→
Tone dial
When setting to 1, the mode is changed by pressing the key from
the pulse dial mode to the tone dial mode.
SW-B4 No. 5 ~ No. 8 Reserved
Set to "0".
SW-B5 No. 1 ~ No. 5 DTMF signal transmission level of lower
frequency
The transmission level of DTMF signal is adjusted. (lower frequency)
00000: 0 dBm
↓
11111: -15.5 dBm (-0.5 dBm x 31)
SW-B5 No. 6 ~ No. 8 Reserved
Set to "0".
SW-B6 No. 1 ~ No. 5 DTMF signal transmission level of higher
frequency
The transmission level of DTMF signal is adjusted. (higher frequency)
00000: 0 dBm
↓
11111: -15.5 dBm (-0.5 dBm x 31)
SW-B6 No. 6 ~ No. 8 Reserved
Set to "0".
SW-C1 No. 1, No. 2 Reading slice (binary)
Used to determine the set value of reading density in standard/fine
mode. The standard setting is "00" (Factory setting is "00")
SW-C1 No. 3, No. 4 Reading slice (half tone)
Used to determine the set value of reading density in half tone mode.
The standard setting is "00" (Factory setting is "00")
SW-C1 No. 5 Line density selection
Used to set the transmission mode which is automatically selected
when the Resolution key is not pressed. In the copy mode, however,
the fine mode is automatically selected unless the Resolution key is
manually set to another mode.
SW-C1 No. 6 ~ No. 8 Reserved
Set to "0".
SW-D1 No. 1 ~ No. 4 Number of rings for auto answer mode
When the machine is set in the auto receive mode, the number of
rings before answering can be selected. It may be set from one to
four rings using a binary number. Since the facsimile telephone could
be used as an ordinary telephone if the handset is taken off the hook,
it should be programmed to the user’s choice. If the soft switch was
set to "1", direct connection is made to the facsimile.
If a facsimile calling beep was heard when the handset is taken off
the hook, press the START key and put the handset on the hook to
have the facsimile start receiving. If it was set to "0" accidentally,
receive ring is set to "1".
NOTE: If the machine is set to answer after a large number of rings, it
may not be able to receive faxes successfully.
If you have difficulty receiving faxes. reduce the number of
rings to a maximum of 6.
SW-D1 No. 5 Automatic switching from manual to auto receive
mode
This soft switch is used to select whether the machine should switch
to the auto receive mode after 5 rings in the manual receive mode or
remain in the same way as SW-D1 No. 1, No. 2, No. 3 and No. 4
"0"1"0"1" (5 rings (UK)) (3 rings (IR)).
SW-D1 No. 6, No. 7 Reserved
Set to "0".
SW-D1 No. 8 Ci detect frequency
Ring signal for auto reception is set.
When this switch is set to "0", PTT standards are set.
SW-D2 No. 1 ~ No. 8 Reserved
Set to "0".
UX-177H
2 – 12