GRAND TOTAL (GT)/ANSWER CHECK SWITCH:
“GT” position: Subtotal (value obtained by pressing
or
) value will automatically be added in the grand total memory.
“•” position: Select this position if ordinary calculations are required without the use of grand total memory or answer check.
“ANSWER CHECK” position: Stores the previous calculation result, and compares the stored value with the subsequent
calculation result.
总和
(GT)
／答案检查开关：
“
GT
”位置：小计（按
或
所得值）值将自动添加到总和内存。
“
•
”位置：
如果只是进行普通计算，而不需要总和记忆或答案检查，请选择该位置。
“
ANSWER CHECK
”位置：存储先前的计算结果，比较存储值和后续计算结果。
DECIMAL POINT ASSIGNMENT SWITCH:
“F” position:
Set the decimal point to “floating” point.
“5,4,3,2,0” positions: The decimal figures can be set to the respective numbers.
“A” position:
Specify the adding mode. For addition and subtraction, the decimal point for entries is positioned
automatically for two decimal places. However, this function does not operate if the
key is used when
entering a value or for calculations other than addition and subtraction.
小数点指定开关：
“
F
”位置：
小数点设置为“浮动”点。
“
5,4,3,2,0
”位置：
小数设置为各个相应数字。
“
A
”位置：
指定加法模式。对于加法和减法，输入数字小数点自动设置为两位小数。如果在输入数值时使用了
键，或加法和减法以外计算时，该功能不可用。
ROUNDING SELECTOR:
Specifies the handling of the digit immediately below the position set by the decimal selector. (For example, if the decimal
selector is set to 3, then the fourth decimal will be rounded.)
“5/4” position: The answer will be rounded off.
“ ” position: The answer will be rounded down.
* While the decimal selector is set to “F” (i.e., floating) position, or if the decimal place cannot be determined (preliminary
calculation results, for instance), the answer will always be rounded down regardless of the setting above.
四舍五入选择器：
指定紧跟小数选择器设定位置后的数字的处理方式。（例如，如果小数选择器设定为
3
，那么第
4
位小数点就会舍入。）
“
5/4
”位置：结果会被上舍入。
“
”位置：结果会被下舍入。
*
当小数选择器设置为“
F
”（即浮点）位置，或如果小数位置不能确定（如初始计算结果），结果将一直下舍入，不受上面设置
影响。
ANSWER CHECK (COMPARISON) /
答案检查（比较）
1. If the answer obtained with
,
agrees with the succeeding tested result, “OK” will be displayed.
2. Pressing
will clear the previously calculated result, disabling the comparison.
3. Answer Check cannot be performed for calculation results obtained by tax calculations, memory calculations, or sampled
values in the middle of a calculation.
1.
如果
、
所得结果与随后检测结果一致，会显示“
OK
”。
2.
按下
将清除先前计算结果，禁止比较功能。
3.
答案检查不能用于税率计算、记忆计算或计算中途取样值的计算结果。
Second calculation /
Ѡ䅵ㅫ
120
)
3
(
)
2
(
3652
670
258
First calculation /
ϔ䅵ㅫ
(1) 120
×
3652
+
670
–
258
=
438652
120
3652
670
258
•
Displayed when it agrees with the previous calculated result. (Not displayed
if it disagrees.)
•
ᔧᅗϢܜࠡ䅵ㅫ㒧ᵰϔ㟈ᯊᰒ⼎DŽ˄ϡϔ㟈ᯊϡᰒ⼎DŽ˅
EL-364(U1C)-1
①