Sharp DV-NC65H, Руководство по обслуживанию

Страница: 61 / 113

61
DV-NC65H/S
DV-NC70H
FLOW CHART NO.6 Is the focus control signal outputted to the pin(115) of IC3701?
Check the pin(118) of IC3701 DAC power source periphery circuit. If it is normal, replace IC3701. Check the line between the IC3704 and the focus actuator. Check CN3301.
Check M 8V line.
Is 8V voltage applied to the pin(22) of IC3704?
Check the pin(21) of IC3704 and replace IC3704.
Is the focus control signal from the pin(115) of IC3701 inputted into the pin(23) of IC3704?
Check the focus control signal line between the IC3701 and IC3704.
Is the focus control drive voltage outputted from the pins(1) and (28) of IC3704?
Is the focus control drive voltage applied to the terminal of focus actuator? Check the connection of optical pickup cable. If it is normal, replace the traverse chassis unit.
No No No No
Yes Yes
Yes No
Yes Yes
The [No Disc] indication.
(In case f
ocus ser
v
o
does
not function.)
FLOW CHART NO.7-1
Check the S 5V line.
Is the control signal outputted from the pin(2) of IC3301? Is 5V voltage applied to the emitter of Q3304? Is approx. 2V applied to the pin(21) of the pickup terminal? (See note.) Check the connection of optical pickup cable. If it is normal, replace the traverse chassis unit.
Check the line between the Q3301, Q3302 and Q3304.
Check or replace IC3301.
No No No
Yes Yes Yes
The [No Disc] indication dur
ing D
VD pla
ybac
k.
(When the laser beam does not light.)
Note: Since the laser diode is very susceptible to static electricity, be careful of static electricity or electricity leak from the measuring equipment when confirming the voltage.
FLOW CHART NO.7-2
Check the S 5V line.
Is the control signal outputted from pin(4) of IC3301? Is 5V voltage applied to the emitter of Q3303? Is approx. 2V applied to the pin(3) of CN3301? Check the connection of optical pickup cable. If it is normal, replace the traverse chassis unit.
Check the line between the Q3301~Q3303. Check or replace IC3301.
No No No
Yes Yes Yes Yes
The [No Disc] indication dur
ing CD pla
ybac
k.
(When the laser beam does not light.)
Note: Since the laser diode is very susceptible to static electricity, be careful of static electricity or electricity leak from the measuring equipment when confirming the voltage.
FLOW CHART NO.8
Check the loading switch. Check for contamination of objective lens of optical pickup. Replace traverse chassis unit.
Do you have loading done the disk by normality? See FLOW CHART NO.9 and NO.10. Set the disc on the disc tray. Replace the Main PWB unit.
Is the level of RF signal which is outputted from pin(31) of IC3301 normal?
No No No
Yes Yes Yes Yes
Both picture and sound do not oper
ate nor
mally
.(1)
FLOW CHART NO.9
Check the PC 5V line.
Set the disc on the disc tray. Are the video signals outputted to the pins of main unit connector CN3202? CN3202 1pin S-Y/COMP CN3202 3pin CB/B CN3202 5pin S-C/R CN3202 7pin CR/B
Check the main unit. (IC3601, Q3201~Q3204 periphery circuit.) Check between CN3202 and CN2701.
No No No
No
No
Yes Yes Yes
Check the V-MUTE line.
Yes Yes
Picture do not oper
ate nor
mally
.
Are the video signals shown above inputted into the pins of IC2701? IC2701 2pin CR/G IC2701 6pin S-Y/COMP IC2701 14pin C/R IC2701 16pin CB/B Are the video signals outputted to each pins of IC2701? IC2701 33pin S-C/R IC2701 31pin COMP IC2701 28pin S-Y IC2701 22pin CB/B IC2701 19pin CR/G
Is 5V applied to the pins(1), (13) and (34) of IC2701?
Replace IC2701. Are the V-MUTE lines at the pins(3) and (15) of IC2701 on "H" level?
*1
*2