Sharp DT300 - DLP Projector - 700 ANSI Lumens, Руководство по обслуживанию

Страница: 3 / 140

3
XV-Z200U/E, XV-Z201E
DT-300
SPECIFICATIONS
This unit has some inactive pixels within acceptable
tolerances which may result in inactive dots on the picture
screen. This will not affect the picture quality or the life
expectancy of the unit. If you have any questions about this
matter, please call toll free 1-877-DTV-SHARP (1-877-388-
7427).
U.S.A. ONLY
Product type
Models
Video system
Display method
DLP panel
Lens
Projection lamp
Video input signal
S-video input signal
Component input signal
(INPUT 1)
Component input signal
(INPUT 2)
Horizontal resolution
RGB input signal
Pixel clock
Vertical frequency
Horizontal frequency
Computer control signal
Rated voltage
Input current
Rated frequency
Power consumption
Heat dissipation
Operating temperature
Storage temperature
Cabinet
I/R carrier frequency
Dimensions (approx.)
Weight (approx.)
Supplied accessories
Replacement parts
Projector
XV-Z200U/DT-300/XV-Z200E/XV-Z201E
PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSC 4.43
DTV 480
I /480P/720P/1080 I /576 I /576P
DLP chip, RGB optical shutter method
Panel size: 0.6
Display method: Single Panel Digital Micromirror Device (DMD™) by Texas Instruments
Drive method: Digital Light Processing (DLP™)
No. of dots: 589,824 dots (1,024 [H]
576 [V])
1–1.2 zoom lens, F1.75–2.04 f=28.0–33.5 mm (XV-Z200U/E), F2.0–2.4 f=16.9–20.2 (XV-Z201E, DT–300)
210 W/168 W SHP lamp
RCA Connector: VIDEO (INPUT 4), composite video, 1.0 Vp-p, sync negative, 75
Ω
terminated
4-pin Mini DIN connector (INPUT 3)
Y (luminance signal): 1.0 Vp-p, sync negative, 75
Ω
terminated
C (chrominance signal): Burst 0.286 Vp-p, 75
Ω
terminated
RCA Connector
Y: 1.0 Vp-p, sync negative, 75
Ω
terminated
P
B
: 0.7 Vp-p, 75
Ω
terminated
P
R
: 0.7 Vp-p, 75
Ω
terminated
29-pin connector
DVI input signal: Digital 250–1,000 mV 50
Ω
Analog 0.7 Vp-p 75
Ω
Y: 1.0 Vp-p, sync negative, 75
Ω
terminated
P
B
: 0.7 Vp-p, 75
Ω
terminated
P
R
: 0.7 Vp-p, 75
Ω
terminated
520 TV lines (NTSC 3.58 input)
DVI-I terminal
<Digital>
Input impedance 50
Ω
Input level 250-1000 mV
<Analog>
Input impedance 75
Ω
Input level 0.7 Vp-p
<Synchronization signal>
•
Separate sync/Composite sync
Input level
TTL level
Input impedance 1 K
Ω
•
Green on sync
Input level (Synchronizing input)
0.286 Vp-p
Input impedance 75
Ω
12–80 MHz
43–75 Hz
15–70 kHz
9-pin D-sub connector (RS-232C Port)
AC 100–240 V
3.2 A
50/60 Hz
285 W
1,070 BTU/hour
41
°
F to 95
°
F ( 5
°
C to 35
°
C)
4
°
F to 140
°
F ( 20
°
C to 60
°
C)
Plastic
38 kHz
14
1 ⁄
2
(W) 6 9 ⁄
16
(H) 12 7 ⁄
8
(D) (368 153.8 327 mm) (including swivel stand)
14
1
⁄
2
(W) 4
5
⁄
8
(H) 12
7
⁄
8
(D) (368 118 327 mm) (main body only)
10.1 lbs. (4.6 kg) (including swivel stand) 9.0 lbs. (4.1 kg) (main body only)
Remote control, Two AA size batteries, Power cord, Terminal cover, Lens cap (attached
on the body), Operation manual, Screws for terminal cover, 21-pin RCA conversion adaptor, Video cable
Lamp unit (Lamp/cage module) (BQC-+1), Remote control
(RRMCGA218WJSA), AA size batteries, Power cord (QACCDA007WJPZ:SEC/SECL, QACCV4002CEZZ:
This SHARP projector uses a DMD chip. This very
sophisticated chip contains 589,824 pixels. As with any high
technology electronic equipment such as large screen TVs,
video systems and video cameras, there are certain
acceptable tolerances that the equipment must conform to.
Specifications are subject to change without notice.
× × × ×
× × × ×
SEEG/SEI, QACCBA012WJPZ:SUK/SRS/SRH/SEEM, QACCLA018WJPZ:SCA/SNZ), Terminal cover
(GCOVAA116WJKB), Lens cap (CCAPHA004WJ01), Operation manual (SEC/SECL:TiNS-B005WJZZ
(XV-Z200U/E)/TiNS-B006WJZZ (XV-Z201E, DT–300), SEEG/SUK:TiNS-B007WJZZ (XV-Z200U/E)/TiNS-
B009WJZZ (XV-Z201E, DT–300), SCA/SNZ/SRS/SRH/SEEM/SEI:TiNS-B008WJZZ (XV-Z200U/E)/TiNS-
B010WJZZ (XV-Z201E, DT–300)), Screws for terminal cover (XBBSN40P10000), 21-pin RCA converter
adaptor (QSOZ0361CEZZ:SEEG/SUK), Video cable (QCNWGA001WJZZ))