18
XV-Z3000
DT-500
RESETTING THE TOTAL LAMP TIMER
●
Resetting the total lamp timer
When replacing the lamp, reset the total lamp timer in the procedure below.
■
The warning lights (power indicator, lamp indicator and temperature warning indicator) on the projector indicate
problems inside the projector.
■
If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate red, and the
projector will enter standby mode. After the projector has entered standby mode, follow the procedures given
below.
Lamp
■
It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes 5% or less,
or when you notice a significant deterioration in the picture and color quality. The lamp life (percentage) can be
checked with the on-screen display.
■
Purchase a replacement lamp of type AN-100LP from your place of purchase, nearest Sharp Authorized Projector
Dealer or Service Center.
About the lamp indicator
When the remaining lamp life becomes 5% or less, (yellow) and "Change The Lamp" will be
displayed on the screen. When the percentage becomes 0%, it will change to
(red), the lamp will
automatically turn off and then the projector will automatically enter standby mode. At this time, the
lamp indicator will illuminate in red.
If you try to turn on the projector a fourth time without replacing the lamp, the projector will
not turn on.
About the temperature warning indicator
If the temperature inside the projector increases, due to blockage of the air vents, or the setting location,
"
" will illuminate in the lower left cor ner of the picture. If the temperature keeps on rising, the lamp
will turn off and the temperature warning indicator will blink, the cooling fan will run, and then the projec-
tor will enter standby mode. After "
" appears, be sure to perform the measures described on page
53
.
Lamp indicator
Temperature warning indicator
Power indicator
Top View
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Connect the power cord.
• Plug the power cord into the AC socket
of the projector.
Reset the lamp timer.
• While simultaneously holding down
MENU, ENTER
and
"
on the pro-
jector, press
STANDBY/ON on the pro-
jector.
• "LAMP 0000H" is displayed, indicating
that the lamp timer is reset.
• Make sure to reset the lamp timer only when
replacing the lamp. If you reset the lamp timer
and continue to use the same lamp, this may
cause the lamp to become damaged or ex-
plode.
1
2
Info
AC socket
ENTER button
MENU button
"
button
STANDBY/ON
button
Содержание DT-500
