background image

29

DK-A10P

DK-A10P (BK)

References

Troubleshooting chart

Many potential problems can be resolved by the owner without
calling a service technician.
If something is wrong with this product, check the following before
calling your authorized SHARP dealer or service center.

General

Remote control

Tuner

 

CD player

iPod

Condensation

Sudden temperature changes, storage or operation in an extremely
humid environment may cause condensation inside the cabinet or on
the transmitter on the remote control.
Condensation can cause the unit to malfunction. If this happens,
leave the power on with no disc until normal playback is possible
(about 1 hour). Wipe off any condensation on the transmitter with a
soft cloth before operating the unit.

If trouble occurs

When this product is subjected to strong external interference
(mechanical shock, excessive static electricity, abnormal supply
voltage due to lightning, etc.) or if it is operated incorrectly, it may
malfunction.

Symptom

Possible cause

The clock is not set to 
the correct time.

Is the Summer Time switch set to the 
correct setting? (Refer to page 14)
Did a power failure occur? Reset 
the clock. (Refer to page 30)

When a button is 
pressed, the unit does 
not respond.

Set the unit to the power stand-by
mode and then turn it back on.
If the unit still malfunctions, reset it. 
(Refer to page 30)

No sound is heard.

Is the volume level set to “0”?

Are the headphones connected?

iPod door not fully 
open/close.

Set the unit to the power  stand-by 
and turn it on again. 
Reset it. (Refer page 30)

Symptom

Possible cause

The remote control does 
not operate.

Is the AC power cord of the unit 
plugged in?
Is the battery polarity correct?
Are the battery dead?
Is the distance or angle incorrect?
Does the remote control sensor 
receive strong light?

Symptom

Possible cause

The radio makes unusual 
noises continuously.

Is the unit placed near the TV or
computer?
Is the FM antenna or AM loop
antenna placed properly? Move
the antenna away from the AC
power cord if it is located nearby.

Symptom

Possible cause

Playback does not start.
Playback stops in the 
middle or does not 
perform properly.

Is the disc loaded upside down?
Does the disc satisfy the standards?
Is the disc distorted or scratched?

Playback sounds are 
skipped, or stopped in 
the middle of a track.

Is the unit located near excessive 
vibrations?
Is the disc very dirty?
Has condensation formed inside the 
unit?

Symptom

Possible cause

No sound is produced.
No image appears on 
the TV/monitor.

The iPod or iPhone is not playing.
The iPod or iPhone is not properly 
connected to the unit.
Is the AC power cord of the unit 
plugged in?
The video cable is not properly 
connected.
The TV/monitor’s input selection is 
not properly set.

iPod or iPhone will not 
charge,

Wrong iPod adaptor is used.
The iPod  or iPhone is not making full 
contact with the iPod connector.
The main unit is in stand-by mode.

Содержание DK-A10P

































Отзывы: