manualshive.com logo in svg

Sharp CV-P10LJ, Инструкция по установке и эксплуатации

Поделиться
Скачать
Sharp CV-P10LJ Скачать руководство пользователя страница 22

Prepare for drainage and drain out water within the unit in the following cases.

• When the unit stops operating and the TIMER, OPERATION and MEGA COOL lamps are 

blinking, the water tank is full and need to be drained.

• When the unit is not used for a long time.

1

  Unplug the power plug and move the unit to a 

drain or outside.

2

  Remove the stopcock from the drainpipe, and 

drain water within the unit.

3

  Replace the stopcock to the drainpipe.

MAIN UNIT OPERATION

DRAINAGE

1

E-

21

Use this mode when the remote control is not available.

1

  Press the POWER button on the unit.

• The red OPERATION lamp on the unit will 

light.

• If the unit has not been unplugged since it 

was last operated, it will resume operation at 
its last settings.

• If the unit has been unplugged since it was 

last operated, it will resume operation in the 
cooling mode, set at 

20

˚

C

. The fan speed set 

to AUTO.

TO TURN OFF

Press the POWER button again.

• The red OPERATION lamp on the unit will turn 

off.

Stopcock

Drainpipe

Содержание CV-P10LJ

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды