Sharp CD-SW440NH, Руководство по эксплуатации

Страница: 29 / 34

04/1/28 CD-SW440N_09 EN
E-20
9
1
7
6
5
4
3
2
1
Setting the clock (Remote control
only)
In this example, the clock is set for the 24-hour (0:00)
display.
To confirm the time display:
Press the CLOCK/TIMER button. The time display will
appear for about 5 seconds.
Note:
The “CLOCK” will appear or time will be displayed when
the AC power supply is restored after a power failure or
unplugging the unit. If incorrect, readjust the clock as
follows.
To readjust the clock:
Perform “Setting the clock” from step 1. If the “CLOCK”
does not appear in step 2, step 3 (for selecting the 24-hour
or 12-hour display) will be skipped.
To change the 24-hour or 12-hour display:
Timer and sleep operation (Remote
control only)
Timer playback:
The unit turns on and plays the desired source (CD,
TUNER, USB, iPod, AUDIO IN, TAPE) at a preset time.
This unit has 2 types of timer: ONCE TIMER and DAILY
TIMER.
Once timer:
Once timer play works for one time only at a preset time.
Daily timer:
Daily timer play works at the same preset time every day.
For example, set the timer as a wake-up call every
morning.
Using the once timer and daily timer in combination:
For example, use the once timer to listen a radio
programme, and use the daily timer to wake up.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CLOCK/TIMER button.
3
Within 10 seconds, press the MEMORY button.
Press the or button to select 24-hour or
12-hour display and then press the MEMORY button.
The 24-hour display will appear.
(0:00 - 23:59)
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
4
To adjust the hour, press the or button and
then press the MEMORY button. Press the or
button once to advance the time by 1 hour. Hold it
down to advance continuously.
5
To adjust the minutes, press the or button and
then press the MEMORY button. Press the or
button once to advance the time by 1 minute.
1
Clear all the programmed contents. [Refer to “Factory
reset, clearing all memory” on page 23 for details.]
2
Perform “Setting the clock” from step 1 onwards.
CD
U S B
TAPE
“0:00”
“AM 12:00”
“AM 0:00”
1
Set the daily timer (pages 20 - 21).
2
Set the once timer (pages 20 - 21).
Before setting timer:
●
Check that the clock is set to the correct time. If it is
not set, you cannot use the timer function.
●
For timer playback: Plug in USB or load discs or dock
iPod to be played.
1
Press the ON/STAND-BY button to turn the power on.
2
Press and hold the CLOCK/TIMER button.
3
Within 10 seconds, press the or button to
select “ONCE SET” or “DAILY SET”, and press the
MEMORY button. Set the clock to the correct time if
“ONCE SET” or “DAILY SET” does not appear.
4
Within 10 seconds, press the or button to
select “TIMER SET”, and press the MEMORY button.
5
To adjust the hour, press the or button and
then press the MEMORY button.
6
To adjust the minutes, press the or button and
then press the MEMORY button.
7
Set the time to finish as in steps 5 and 6 above.
8
To select the timer playback source (CD, TUNER, USB,
iPod, TAPE or AUDIO IN), press the
or button.
Press the MEMORY button.
When you select the tuner, select a station by pressing
the
or button, and then press the MEMORY
button. If a station has not been programmed, “NO
PRESET” will be displayed and timer setting will be
cancelled.
9
Adjust the volume using the VOLUME control, and then
press the MEMORY button. Do not turn the volume up
too high.
Once timer
Daily timer
Start
Stop
1 minute or more
Start Stop
Timer playback