CD-BA200
– 2 –
FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER
TO THE OPERATION MANUAL.
IMPORTANT SERVICE NOTES (FOR U.S.A. ONLY)
BEFORE RETURNING THE AUDIO PRODUCT
(Fire & Shock Hazard)
Before returning the audio product to the user, perform the
following safety checks.
1. Inspect all lead dress to make certain that leads are not
pinched or that hardware is not lodged between the chassis
and other metal parts in the audio product.
2. Inspect all protective devices such as insulating materials,
cabinet, terminal board, adjustment and compartment covers
or shields, mechanical insulators etc.
3. To be sure that no shock hazard exists, check for leakage
current in the following manner.
* Plug the AC line cord directly into a 120 volt AC outlet.
* Using two clip leads, connect a 1.5k ohm, 10 watt resistor
paralleled by a 0.15
µ
F capacitor in series with all exposed
metal cabinet parts and a known earth ground, such as
conduit or electrical ground connected to earth ground.
* Use a VTVM or VOM with 1000 ohm per volt, or higher,
sensitivity to measure the AC voltage drop across the
resistor (See diagram).
* Connect the resistor connection to all exposed metal parts
having a return path to the chassis (antenna, metal cabinet,
screw heads, knobs and control shafts, escutcheon, etc.)
and measure the AC voltage drop across the resistor.
All check must be repeated with the AC line cord plug connection
reversed.
Any reading of 0.3 volt RMS (this corresponds to 0.2 milliamp.
AC.) or more is excessive and indicates a potential shock
hazard which must be corrected before returning the audio
product to the owner.
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
TEST PROBE
0.15 µ F
1.5k ohms
10W
VTVM
AC SCALE
General
Power source:
AC 120 V, 60 Hz
Power consumption:
185 W
Dimensions:
Width; 10-5/8" (270 mm)
Height; 13" (330 mm)
Depth; 14" (355 mm)
Weight:
19.2 lbs. (8.7 kg)
Amplifier section
Output power:
100 watts minimum RMS per
(Except for Canada)
channel into 6 ohms from 60 Hz
to 20 kHz, 10 % total harmonic
distortion
Output power:
RMS; 200 W (100 W + 100 W)
(For Canada)
(10% T.H.D)
[Main speaker (woofer,
tweeter and super
tweeter);
80 W (40 W + 40 W),
Subwoofer;
120 W (60 W + 60W)]
Output terminals:
Speakers; 6 ohms
Headphones; 16-50 ohms
(recommended; 32 ohms)
Input terminals:
Video/Auxiliary (audio signal);
500 mV/47 kohms
Compact disc player section
Type:
3-disc multi-play compact disc
player
Signal readout:
Non-contact, 3-beam semi-
conductor laser pickup
D/A Converter:
1-bit D/A converter
Specifications for this model are subject to change without
prior notice.
SPECIFICATIONS
CD-BA200
Frequency response:
20 - 20,000 Hz
Dynamic range:
90 dB (1 kHz)
Tuner section
Frequency range:
FM; 87.5 - 108 MHz
AM; 530 - 1,720 kHz
Cassette deck section
Frequency response:
50 - 14,000 Hz (Normal tape)
Signal/noise ratio:
55 dB (TAPE 1, playback)
50 dB (TAPE 2, recording/
playback)
Wow and flutter:
0.3 % (WRMS)
Speaker section
Type:
4-way type [5-1/4" (13 cm) sub
woofer, 5-1/4" (13 cm) woofer,
2" (5cm) tweeter and super
tweeter]
Maximum input power
(Total):
200 W
Rated input power
(Total):
100W
Impedance:
6 ohms
Dimensions:
Width; 10-5/8" (270 mm)
Height; 13" (330 mm)
Depth; 10-3/8" (264.6 mm)
Weight:
10.3 lbs. (4.7 kg)/each
CP-BA200
Содержание CD-BA200
Страница 48: ...CD BA200 48 M E M O ...
