TINSEA955WRRZ-D32 SEC R220/216/214FW O/M
3
SEC R220/216/214FW O/M
Safety door latches
Hinges
Door seals and
sealing surfaces
Waveguide
cover
Unpacking and Examining Your Oven
Remove:
1. all packing materials from inside the oven
cavity; however, DO NOT REMOVE THE
WAVEGUIDE COVER, which is located on
the right cavity wall.
Read enclosures
and SAVE the Op-
eration Manual.
2. the feature sticker,
if there is one, from
the outside of the
door.
Check the oven for
any damage, such
as misaligned or bent door, damaged door
seals and sealing surfaces, broken or loose
door hinges and latches and dents inside the
cavity or on the door. If there is any damage,
do not operate the oven and contact your
dealer or SHARP AUTHORIZED SERVICER.
Choosing a Location for Your Oven
You will use the oven frequently so plan its
location for ease of use. It's wise, if possible,
to have counter space on at least one side of
the oven. Allow at least 2 inches on the sides,
top and at the rear of the oven for air circula-
tion. Do not place or install the oven in any
area where heat and steam are generated; for
example, next to or above a conventional gas
or electric range or above a conventional wall
oven. Heat and steam may damage the elec-
tronics or the mechanical parts of the oven.
U N PA C K I N G A N D I N S TA L L AT I O N I N S T R U C T I O N S
G R O U N D I N G I N S T R U C T I O N S
This appliance must be grounded. This oven is equipped with a cord having a grounding wire
with a grounding plug. It must be plugged into a wall receptacle that is properly installed and
grounded in accordance with the National Electrical Code and local codes and ordinances. In
the event of an electrical short circuit, grounding reduces risk of electric shock by providing an
escape wire for the electric current.
WARNING
- Improper use of the grounding plug can result in a risk of electric shock.
Electrical Requirements
The electrical requirements are a 120 volt 60 Hz, AC only, 15
amp. or more protected electrical supply. It is recommended
that a separate circuit serving only this appliance be provided.
The oven is equipped with a 3-prong grounding plug. It must
be plugged into a wall receptacle that is properly installed and
grounded. Should you only have a 2-prong outlet, have a quali-
fied electrician install a correct wall receptacle.
A 3-prong adapter may be purchased and used temporarily if
local codes allow. Follow package directions.
A short power-supply cord is provided to reduce risk of becom-
ing entangled in or tripping over a longer cord.
Extension Cord
If it is necessary to use an extension cord, use only a 3-wire extension
cord that has a 3-blade grounding plug and a 3-slot receptacle that will
accept the plug on the microwave oven. The marked rating of the exten-
sion cord should be AC 115-120 volt, 15 amp. or more.
Be careful not to drape the cord over the countertop or table where it
can be pulled on by children or tripped over accidentally.
Notes:
1. If you have any questions about the grounding or electrical
instructions, consult a qualified electrician or service person.
2. Neither Sharp nor the dealer can accept any liability for damage to the oven or personal
injury resulting from failure to observe the correct electrical connection procedures.
Radio or TV Interference
Should there be any interference caused by the microwave oven to your radio or TV, check
that the microwave oven is on a different electrical circuit, relocate the radio or TV as far
away from the oven as feasible or check position and signal of receiving antenna.
SEC R220/216/214FW,P01-10
03.5.22, 8:43 PM
3
Содержание Carousel R-214F
Страница 21: ...19 NOTES ...
Страница 22: ...20 NOTES ...
