Sharp AR-317 Operation Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 302

background image

4

Be sure to connect the power cord only to a power outlet that meets the specified voltage and
current requirements. Also make certain the outlet is properly grounded.

Be sure to allow the required space around the
machine for servicing and proper ventilation.

CAUTIONS ON HANDLING THE MACHINE

Observe the following precautions when handling the machine to maintain top performance.

Do not drop the machine, subject it to shock or strike it against any object.
Store spare toner cartridges in a cool dry place without removing from the package before use.

• If they are exposed to direct sunlight or excessive heat, poor copies may result.

Do not touch the photoconductive drum (green portion).

• Scratches or smudges on the drum will cause dirty copies.

Connect the machine to a power outlet which is not used for other electric appliances. If a lighting fixture is
connected to the same outlet, the light may flicker.

Note

12" (30cm)

12"

(30cm)

12"

(30cm)

A small amount of ozone is produced within the machine during operation.
The emission level is insufficient to cause any health hazard.

Note:

The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 m

g/

m

3

) calculated as an 8 hr. time-

weighted average concentration.
However, since the small amount that is emitted may have an objectionable odor, it is advisable to place the
machine in a ventilated area.

Safety precautions:

This Digital Copier is rated Class I and complies with 21 CFR 1040.10 and 1040.11 of the CDRH standards. This
means that the machine does not produce hazardous laser radiation. For your safety, observe the precautions below.
• Do not remove the cabinet, operation panel or any other covers.
• The machine’s exterior covers contain several safety interlock switches. Do not bypass any safety interlock by

inserting wedges or other items into switch slots.

This product utilizes a CR coin Lithium battery which contains a Perchlorate material. Special handling for this
material may apply, California residents, See www.dtsc.ca.gov/hazardouswaste/perchlorate/
Others, consult local environmental officers.

!Andromeda_copy_sec.book 4 ページ２００６年１１月２３日　木曜日　午後６時１分

«
...
28
29
30
31
32
...
»

Содержание AR-317 Operation















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AR-317 Operation

imageRUNNER ADVANCE C350iF

Бренд: Canon Страницы: 102

imageRUNNER ADVANCE C2230

Бренд: Canon Страницы: 12

Бренд: Canon Страницы: 598

Бренд: Panasonic Страницы: 486

Бренд: Pinnacle Technology Страницы: 76

Бренд: Oce Страницы: 340

Бренд: Muratec Страницы: 112

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 182

Бренд: Ricoh Страницы: 301

giant 100 series

Бренд: Sam4s Страницы: 54

Бренд: Olivetti Страницы: 204

ExpressCard 500

Бренд: Magtek Страницы: 49

Бренд: Ricoh Страницы: 284

Бренд: MHM Страницы: 52

Бренд: SATO Страницы: 2

Бренд: Oki Страницы: 239

Бренд: Olivetti Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды