Sharp AR-235 Скачать руководство пользователя страница 61

Страница: 61 / 158

IAL FUNCTIONS

TRANSPARENCY

The TRANSPARENCY feature is used to copy onto transparency film.

●

When copying onto transparency film, use this feature to obtain better copy quality. When this feature
is selected, the bypass tray will be automatically selected and "TRANSPARENCY" will appear in the
paper size display.

●

This feature cannot be used with duplex copying or staple sort copying.

Place an original on the platen glass or in the document feeder tray.

Press the SPECIAL FUNCTION key. Then press the OK key.

●

The SPECIAL MODES screen will appear.

Use the and keys to select "TRANSPARENCY" and press the OK
key.

●

A check mark will appear to the left of "TRANSPARENCY", and the display will return to
the basic screen.

Document feeder tray

SPECIAL MODES

MARGIN SHIFT

ERASE

DUAL PAGE COPY

[OK]:ADJUST

SPECIAL MODES

XY ZOOM

B/W REVERSE

TRANSPARENCY

[OK]:OFF ON

00EX.book 59 ページ２００１年５月２５日金曜日午前１０時４９分

Содержание AR-235































































































































































Результаты поиска

Содержание AR-235

Отзывы:

Бренды по названию

Популярные бренды

Sharp AR-235, Руководство по эксплуатации

Результаты поиска

Содержание AR-235

Отзывы:

Бренды по названию

Популярные бренды