Sharp Aquos LC-60LE740E Скачать руководство пользователя страница 65

Страница: 65 / 204

LC-60/70LE740E/RU,741E/S,743E,60LE840E/RU,841E/S,843E,80LE645E/RU,646E/S,648E

5 – 21

8. When all the procedures are complete, the following upgrade success screen shows up.

The new software version can be confirmed on screen.

After a while, Turn off power and boot-up automaticaly.

NOTE: TV is restarted automaticaly, the AC code need not be pulled out.

9. After boot-up, the following caution shows up.

Select OK when if there is no problem.

Software update is completed, please remove the USB memory device.

NOTE: Then get the set started and call the process adjustment screen (Top Page) to check the main software version.

Update version

xxxxxxxxxxxx

[Information

Software update

USB update]

Software Update is complete.

System software was successfully updated.

Remove the USB memory device.

Update version

: EXXXXXXX-2

Содержание Aquos LC-60LE740E













































































































































































































Результаты поиска

Содержание Aquos LC-60LE740E

Отзывы:

Похожие инструкции для Aquos LC-60LE740E

Бренды по названию

Популярные бренды

Sharp Aquos LC-60LE740E, Руководство по обслуживанию

Результаты поиска

Содержание Aquos LC-60LE740E

Отзывы:

Похожие инструкции для Aquos LC-60LE740E

Бренды по названию

Популярные бренды