Attaching the stand (Continued)
Viewing E-Manual
Viewing the Built-in Operation Manual
2
1
Displays the built-in operation manual on the screen.
You can read information about how to use this device.
1
Press
(HOME)
to display the HOME screen,
press
/
/ / to select
(Manual)
icon, and
then press
ENTER
.
This displays the built-in operation manual screen.
2
When you select contents, its page will be
displayed.
Appendix
Troubleshooting
The problems described below are not always caused by malfunctions. Check the TV again before having the TV serviced.
Problem
Possible Solution
•
No power.
•
Check if you pressed
POWER
on the remote control unit.
•
Is the AC cord disconnected?
•
Has the power been turned on?
•
Remote control unit does
not operate.
•
Are batteries inserted with polarity (+, –) aligned?
•
No picture.
•
Is connection to other components correct?
•
No sound.
•
Is connection to other components correct?
CLEARING THE PASSWORD
If you forget the password, clear the password using the following procedure.
1
From the ATV/DTV screen, select “Tools” > “Basic settings” > “Function settings” > “Security & Restrictions” >
“Parental Control” > “Password”, and then press
ENTER
and the password input screen will display.
2
Enter “3001” using
0 – 9
, select “Disable” in the password settings, and then select “Enable” to reset password.
3
Select “Back to settings”.
4
Select “Password” then select “Enable” to set password for parental control.
5
Enter the 4-digit number as a password using
0
–
9
,
and then enter the same 4-digit to confi rm. The new password
is now set.
- 7
- 8
2
Fix the stand mounting bracket and stand base
with 4 pieces of the screws (large) for assembling
the stand.
Rear
Front
3
Prepare a table and lay the display portion on it.
•
To prevent damage to the LCD panel, spread a soft
cloth such as a blanket on the table and lay the
display portion on it.
•
Do not remove protective sheet until fi nish the
setting.
4
Attaching the stand to the main unit.
•
Make sure that the 4 tabs on the stand mounting
bracket are securely inserted into the holes on the
main unit.
CAUTION
•
After laying down the TV, do not push it inside to prevent
damage to the indicator. Please be more careful.
NG
OK
TV
Example
Example
TV
Table or Box
Table or Box
5
Fix the stand with 4 pieces of the mounting screws
(large) for stand and then tighten the screws.
Do not leave a gap
between the groove on
the main unit and the
tabs on the stand.
6
Attach the stand cover.
•
Slide the stand cover in the arrow direction and
attach it with the mounting screw for stand cover
(small).
CAUTION
•
After fi xing the stand, make sure that the stand
is not loose or wobbling and all the screws are
securely tightened.
•
When raising up the TV, please do not push the TV
surface by fi nger.
How to adjust angle
(Be careful not to pinch your fi ngers)
•
Turn the main unit while being careful not to pinch your
hand.
The angle can be adjusted within the range of
approximately 15 degrees to the right and left.
Approx. 15°
Approx. 15°
Detaching the stand
•
Please take care the LED part in front of TV. For detach
the stand base, perform the above steps in reverse
order.
•
To prevent damage to the LCD panel, spread a soft
cloth such as a blanket on the table and lay the display
portion on it.
CAUTION
•
If you remove screws with TV stand-up position, there is
a big risk that the TV will falling down.
8T-C6070DW1X_H493.indb 4
8T-C6070DW1X_H493.indb 4
23/2/2021 5:41:24 PM
23/2/2021 5:41:24 PM
Содержание AQUOS 8T-C60DW1X
Страница 6: ......
