background image

AL-1551 COPY PROCESS 6-3

Step-3: Developing (DC bias)

A bias potential is applied to the MG roller in the two component
magnetic brush developing method, and the toner is charged negative

through friction with the carrier.

Non-image area of the drum surface charged with negative potential
repel the toner, whereas the laser exposed portions where no negative

charges exist, attract the toner. As a result, a visible image appears on

the drum surface.

Toner is attracted over the shadowed area because of the developing

bias.

Step-4: Transfer

The visible image on the drum surface is transferred onto the print paper
by applying a positive charge from the transfer corona to the backside of

the print paper.

Step-5: Separation

Since the print paper is charged positively by the transfer corona, it is

discharged by the separation corona. The separation corona is
connected to ground.

Step-6: Cleaning

Toner remaining on the drum is removed and collected by the cleaning
blade. It is transported to the waste toner collecting section in the

cleaning unit by the waste toner transport roller.

S

N

N

:Carrier (Magnetized particle)
:Toner (Charge negative by friction)
(N) (S) Permanent magnet

(provided in three locations)

MG roller

 

DC
400V   8V

About DC 5.2kV

  )    ! "#$%&'

Содержание AL-1043































































































































Отзывы: