Sharp A1000 - B/W Inkjet - Fax Скачать руководство пользователя страница 120

Страница: 120 / 136

Messages and Signals

118

LINE ERROR

Transmission or reception was not successful. Press
the

STOP

key to clear the message and then try

again. If the error persists, see

Line error on page

113.

LOW INK

The cartridge is low on ink (approximately one
quarter of the ink remains).

MEMORY IS FULL

If faxes have been received to memory because
printing is not possible (an additional message will
indicate the problem), resolve the problem so that
printing can continue (see

Substitute Reception to

Memory on page 84).
If you are attempting to transmit from memory, see

the memory becomes full on page 77.
If you are copying, see

If MEMORY IS FULL appears

on page 86.

MEMORY PRINTING

The fax is preparing to or printing out a document
from memory.

NO # STORED

This appears if you attempt to search for an auto-dial
number when none have been stored.

OFF HOOK

This appears if you forgot to replace the handset after
using it to dial and send a fax. Replace the handset or
press the

STOP

key to clear the message.

ON HOOK DIAL

The

SPEAKER

key has been pressed and the fax

machine is waiting for you to dial.

OUT OF INK

The cartridge is out of ink and must be replaced.
Faxes will be received to memory.

PAPER JAMMED

The printing paper is jammed. See page 121.

PRINTER ERROR

A printer error has occurred. Open the printer
compartment cover, make sure the print cartridge is
installed correctly, and then close the cover.

PRINTER ERROR/
CHECK PAPER

A paper jam may have occurred. Follow the
procedure on page 121 to clear the jam.

all.book Page 118 Wednesday, November 12, 2003 9:50 AM

Содержание A1000 - B/W Inkjet - Fax









































































































































Результаты поиска

Содержание A1000 - B/W Inkjet - Fax

Отзывы:

Похожие инструкции для A1000 - B/W Inkjet - Fax

Бренды по названию

Популярные бренды

Sharp A1000 - B/W Inkjet - Fax, Руководство по эксплуатации

Результаты поиска

Содержание A1000 - B/W Inkjet - Fax

Отзывы:

Похожие инструкции для A1000 - B/W Inkjet - Fax

Бренды по названию

Популярные бренды