6
TOLL FREE: 1-800-798-7398
7
www.sharkclean.com
ASSEMBLY OF YOUR FLOOR
AND CARPET CLEANER:
NOTE:
The charging adapter
will be shipped inside the foam
packaging.
1
Slide the upper pole (the tube
with the handle) into the end
of the Shark
®
Backsaver
™
joint
that has a small notch in it (
a
).
Then slide the lower pole into
the other end of the joint (
b
).
Push it in until it clicks into
place. (
Fig. 1
)
COMPONENTS:
A
Main Unit
B
Speed Control Button
C
Power Button
D
Dust Container
E
Backsaver
™
Release Button
F
Upper Pole with Handle
G
Shark
®
Backsaver
™
Joint
H
Lower Pole
I
Dust Container Empty Button
J
Charging Adapter
Fig. 1
Fig. 2
E
I
ASSEMBLY
F
G
H
J
2
Insert the Shark
®
Backsaver
™
folding handle you just
assembled into the top of the
unit. You should hear the
locking tab click into place.
(
Fig. 2
)
IMPORTANT:
You must charge
the batteries for 24 hours before
using the unit for the first time.
See page 7 for instructions on
charging your unit.
C
A
B
D
Model Number:
V1950 N 32
Voltage:
7.2 V
If the brush roll stops moving, it’s probably due
to the anti-jam feature. This feature protects
the motor from becoming overheated. If the
brush becomes overloaded, it will stop turning
and both speed indicator lights will stay on.
Turn off your unit by pressing the power button
once. See page 9 for instructions on removing
or cleaning the brush roll. Wait for 10 seconds
to let your unit cool down. Now press the
power button again and you’re ready to resume
cleaning!
NOTE:
Charge the batteries for
24 hours before first use.
1
Always make sure that the unit
is turned off. (
Fig. 3
)
2
Insert the charger plug into the
hole on the side of the unit.
Plug the charger into a wall
outlet. The light next to the
power button will illuminate
when the unit is charging. If the
unit is plugged in and the light is
not illuminated, press the power
button once. The light should
now be illuminated indicating
that the unit is charging.
(
Fig. 4
)
CHARGING YOUR CORDLESS FLOOR AND CARPET CLEANER
3
After first use, recharge for 16
hours. Your cordless floor and
carpet cleaner is powered by
Ni-Cd batteries that need this
time to build up their charge.
4
Always remove the charging
adapter from the unit after the
charging period has completed.
Storing the unit with the
adapter attached and
plugged in will reduce the
battery life.
IMPORTANT:
Although many
adaptors look similar, it’s
important to use only the
adaptor that came with the unit
(KA12D090015023U).
To maintain peak
performance of your cordless
floor and carpet cleaner,
let the battery run down
completely at least once a
month and then recharge it.
indicates the speed optimized to
clean bare floors and two lights
indicate the speed optimized to
clean carpets and larger debris
on bare floors. (
Fig. 6
)
1
Press the power button to start
the unit. The lights on the unit
will illuminate. When finished
cleaning, press the power
button again to turn the unit
off. (
Fig. 5
)
USING YOUR CORDLESS FLOOR AND CARPET CLEANER
2
You can adjust the speed of the
brush roll to suit the floors that
you are cleaning. Press the
button on the right (opposite
the power button) to switch
between speeds. One light
Fig. 3
Fig. 4
Fig. 5
Fig. 6
FLOOR
CARPET
OFF
a
b
V1950_N_32_ENG_IB_100928.indd 6-7
28/09/10 4:21 PM
