Shark SSG-403037E Скачать руководство пользователя страница 4

SSG฀579-585฀฀•฀9.801-193.0฀฀•฀฀Rev.฀3/14

OPERA

T

OR’S MANU

AL

   

PRESSURE W

ASHER

  

4

14.  Never make adjustments on machine while in  

operation.

 15. Be certain all quick coupler fittings are secured 

before using pressure washer.

 

RISK OF INJECTION 
OR SEVERE INJURY 

TO PERSONS. KEEP 

CLEAR OF NOZZLE.

WARNING

WARNING: High pressure devel-

oped by these machines will 
cause personal injury or equip-
ment damage. Keep clear of 
nozzle. Use caution when oper-
ating. Do not direct discharge 
stream at people, or severe in-
jury or death will result. 

 

WARNING

PROTECT FROM 

FREEZING

WARNING: Protect machine from 

freezing.

16.  To keep machine in best  
 

operating conditions, it is  

 

important you protect machine  

 

from freezing. Failure to protect  

 

m a c h i n e   f r o m   f r e e z i n g 

 

 

could cause malfunction of the  

 

machine and result in death, 

serious bodily injury, and/or property damage. Fol-
low storage instructions specified in this manual.

17.   Inlet water must be clean fresh water and no hotter 

then 90°F.

 

WARNING

RISK OF 

ASPHYXIATION:  

USE THIS  PRODUCT 

ONLY IN A WELL 

VENTILATED AREA.

WARNING: Risk of asphyxiation. 

Use this product only in a well 
ventilated area. 

 18.  Avoid installing machines in 

small areas or near exhaust 
fans. Adequate oxygen is 
needed for combustion or 
dangerous carbon monoxide 
will result.

 19. Manufacturer will not be liable for any changes 

made to our standard machines or any components 
not purchased from us.

 20. The best insurance against an accident is  

precaution and knowledge of the machine.

IMPORTANT SAFETY INFORMATION

 

  In an overfilling situation, additional precautions are 

necessary to ensure that the situation is handled 
in a safe manner.

WARNING: Risk of injury. Disconnect battery 
ground terminal before servicing.

  8.  When in use , do not place machine near flammable 

objects as the engine is hot.

  9. Oil burning appliances shall be installed only in 

locations where combustible dusts and flammable 
gases or vapors are not present. Do not store or 
use gasoline near this machine.

 10.  Use No. 1 or No. 2 heating oil (ASTM D306) only. 

NEVER use gasoline in your fuel oil tank. Gasoline 
is more combustible than fuel oil and could result 
in a serious explosion. NEVER use crankcase or 
waste oil in your burner. Fuel unit malfunction could 
result from contamination.

 11.  Do not confuse gasoline and fuel oil tanks. Keep 

proper fuel in proper tank.

WARNING

RISK OF INJURY.  

HOT SURFACES  

CAN CAUSE BURNS

WARNING: Risk of injury. Hot 

surfaces can cause burns. Use 
only designated gripping areas 
of spray gun and wand. Do not 
place hands or feet on non-insu-
lated areas of the pressure 
washer.

 12.  Transport/Repair with fuel tank EMPTY or with fuel 

shut-off valve OFF. 

 

HOT  DISCHARGE  FLUID:   

DO NOT TOUCH OR 

DIRECT DISCHARGE 

STREAM AT PERSONS.

CAUTION: Hot discharge fluid. 
Do not touch or direct discharge 
stream at persons.

WARNING: This machine pro-
duces hot water and must have 
insulated components attached 
to protect the operator.

 13.  To reduce the risk of injury, close supervision is nec-

essary when a machine is used near children. Do 
not allow children to operate the pressure washer. 
This machine must be attended during operation. 

 

TRIGGER GUN KICKS 

BACK - HOLD WITH  

BOTH HANDS

WARNING

WARNING: Grip cleaning wand 

securely with both hands before 
starting. Failure to do this could 
result in injury from a whipping 
wand.

Содержание SSG-403037E









































Отзывы: