manualshive.com logo in svg

Shark SSD-603567E, Руководство оператора, Страница: 9 / 42

Поделиться
Скачать
Shark SSD-603567E Скачать руководство пользователя страница 9

 SSD •  9.801-194.0  •   Rev.  12/13

9

 PRESSURE W

ASHER

  

OPERA

TOR’S MANU

AL

  

98011940-20

 

 

 

 

 

 

 

 

98011940-17

Safety 

Latch

OPERATING INSTRUCTIONS

98011940-16

STEP 1:

 Read operator's manual before operating machine. Check engine 

oil level. Oil level should be level with the bottom of the oil filler neck. (Refer 
to the engine’s operating manual included with machine.) We recommend 
that the oil be changed after the first 50 hours of use, then once every 
250 hours. 

NOTE:

 Improper oil levels will cause low oil sensor to shut off 

engine. 

 IMPORTANT! Do not run engine with high or low oil levels 

as this will cause engine damage.

STEP 2:

 Fill engine fuel tank with 

No. 2 diesel fuel. Check engine and 
pump oil levels. Check engine ra-
diator fluid level. Install battery and 
connect red cable to the + terminal 
and black to the - terminal.

Oil Dipstick

Fuel  

Tank

STEP 3:

 Read engine manual. The 

keyed ignition is located on the en-
gine control panel. Turn key to first 
position. The glow plug light will illu-
minate. When the light goes out, turn 
key to start (second) position. Do not 
hold key in start position longer than 
five (5) seconds or starter motor will 
be damaged.

STEP 4:

 Before installing pres-

sure nozzle, trigger spray gun to 
eliminate trapped pressure. Then 
run machine allowing water to flush 
through the system until clear.

STEP 5:

 With spray gun and wand 

pointed away from you or anybody 
else, insert pressure nozzle into 
quick coupler on end of wand.  
Press trigger on spray gun to obtain  
pressurized cold water spray.

WARNING! Never replace noz-

zles without engaging the safety 
latch on the spray gun trigger.

Oil Cap Filter

98011940-19

STEP 6:

 For hot water, turn the 

burner switch to ON when a steady 
stream of water flows out of the 
spray gun. Burner will light auto-
matically.

NOTE:

 Do not start machine with 

burner switch on.

STEP 7:

 To apply detergent, place 

detergent pick-up tube into a con-
tainer of detergent and turn the 
detergent valve counterclockwise.

STEP 8:

 To stop, reverse steps 

and set all controls to their original 
settings. 
Turn burner switch OFF and open 
trigger on spray gun, allowing water 
to cool.

98011940-18

Key 

Switch

Trigger

98011940-18

Burner 
Switch

 

 

 

 

 

 

 

98011940-21

Detergent 

Valve

98011940-18

Burner 
Switch

Содержание SSD-603567E











































Отзывы:

Нет отзывов