manualshive.com logo in svg

Shapeways FLETTNER FL-282 V21 KOLIBRI, Руководство пользователя

Поделиться
Скачать
Shapeways FLETTNER FL-282 V21 KOLIBRI Скачать руководство пользователя страница 2

Dear customer, 
 
We  thank  you  for  buying  our  products  &  we  appreciate  your  interest  on 
our 1/18 scale Flettner FL-282 V21 Kolibri “cutaway” model kit which is a 
frame-only version of our previously released 

1/18 scale Flettner Fl-282 

Kolibri helicopter model kit

. It would make a fine cutaway diorama display. 

 
In  case  you  ‘ll  notice  slight  traces  of  oil on the parts surface when you 
got the kit, it is absolutely normal. This oil is actually left after the 3D 
printing  process  was  finished  and  the  kit  parts  been  removed  from  the 
printer  tray  to  be  washed  into  an  ultrasonic  oil  bath  and  later  an 
ultrasonic  water  bath  and  might  escaped  the  clean  inspection  and  dry  by 
hand procedure. So, if you notice oily traces, the 3D printed kit parts can 
be cleaned easily by sinking everything into a plastic bowl filled with White 
Spirit and then place them on soft paper towels and allow to dry. 
 
Feel  free  to  ask  any  help  or  info  during  the  model  building  process.  You 
already got the assembling instructions in your hands, but we ’ll be next 
to you for anything you need in order to build a fine realistic scale model. 
 
Regards, 
 
Anyuta 3D print creations & scale models 

http://www.shapeways.com/shops/anyuta3D

 

Содержание FLETTNER FL-282 V21 KOLIBRI




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды