SGS SAT110K Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 13

SGS SAT110K Скачать руководство пользователя страница 10

PAGE 10

CARE & MAINTENANCE - RATCHET WRENCH

The tool should be lubricated daily (or before each use) with air tool oil (not in-
cluded). Air tool oil is available from SGS Engineering. Do not use detergent oil.
During continuous operation, the tool should be oiled every 1 to 2 hours. This may
be done using an in-line oiler or manually. If done manually, proceed as follows:

1. Disconnect the tool from air supply. (See Figure 4)
2. Place a few drops of air tool oil into the air inlet. (See Figure 5) Avoid the misuse
of thicker oil which may lead to the reduced performance or malfunction.
3. Connect the tool to the air supply. Run the tool without load for a few seconds
to distribute the oil through the tool. Any excess oil may be propelled from the air
exhaust area so point the tool in a safe direction.
4. After operating the tool and before storing the tool, disconnect the air hose and
place 4 or 5 drops of air tool oil into the air inlet, then re-connect the air hose and
run the tool to evenly distribute the oil throughout the tool for approximately 30
seconds. This will prolong the tool life.
5. Avoid storing the tool in a humid environment which promotes rusting of internal
mechanisms. Always oil the tool before storage.

OPERATING INSTRUCTIONS - RATCHET WRENCH

1. Lubricate the tool before operating. See “CARE AND MAINTENANCE” section

for oiling instructions.

2. Choose the correct impact socket as needed and mount it onto the square-

drive. (See Figure 1)

3. Remove the air inlet protective cap from the tool and mount a male plug. Con-

nect air supply hose to the tool. Set the air pressure at 90 PSI. (See Figure 2)

4. To install/tighten threaded fasteners push the F/R stem (Part #29) foward to “F”

position. Press the trigger. Then the tool runs clockwise. (See Figure 3)

5. To remove/loosen threaded fasteners push the F/R stem (Part #29) backwards

to “R” position. Press the trigger. Then the tool runs counterclockwise. (See
Figure 3)

WWW.SGS-ENGINEERING.COM

«
...
8
9
10
11
12
...
»

Содержание SAT110K














Отзывы:

Нет отзывов