SGS 58CC Скачать руководство пользователя

Страница: 9 / 46

PAGE 9

KICKBACK PREVENTION

Kickback may occur when the nose or tip of
the guide bar touches an object, or when
the wood closes in and pinches the saw
chain in the cut.

Tip contact in some cases may cause a
lightning fast reverse reaction, kicking the
guide bar up and back towards the opera-
tor.

Pinching the saw chain along the top of the
guide bar may push the guide bar rapidly
back towards the operator.

Either of these reactions may cause you to
Iose control of the saw, which could result in
serious personal injury.

Do not rely exclusively on the safety devices
built into your saw. As a chain saw user you
should take several steps to keep cutting
jobs free from accident or injury- such as:

-Steady, methodical work
-Proper revision of this manual
-Good dilligance
-A clear visual of your work area

Содержание 58CC















































Результаты поиска

Содержание 58CC

Отзывы:

Похожие инструкции для 58CC

Бренды по названию

Популярные бренды

SGS 58CC, Руководство пользователя

Результаты поиска

Содержание 58CC

Отзывы:

Похожие инструкции для 58CC

Бренды по названию

Популярные бренды