background image

9

• 

SFERASOL

TM

 must be installed in a place with total daytime sunlight. If not possible, 

sunlight should be at least from 11 a.m. to sunset.  
• When installed, 

SFERASOL

TM

  inspection door must be always SOUTH-side oriented 

• In order to avoid temperature losses due to piping length, 

SFERASOL

TM

 panel should 

be positioned next to the Storage tank and/or to the collection point.
• After installation, ensure that 

SFERASOL

TM

 is protected against wind which reduces 

the greenhouse e

 ect obtained by the spherical shape of the system.

• Any changes to the optimal orientation would reduce 

SFERASOL

TM

 e

  ciency, with no 

responsibility of 

SFERASOL

TM

 panel.  

• In case optimal installation is not possible, the number of 

SFERASOL

TM

 panels requi-

red would increase to compensate e

  ciency losses.

• Shading (due to trees, buildings or any other obstacles) should be avoided in order to 
ensure at least 4-6 hours of complete sunshine exposure during maximum sun thermal 
radiation.
• Basement on which the machine will be positioned must be planned so that is sui-
table to hold the machine weight
• A well corresponding to the appliance base should be advisable and lay underground  
a piping connection for water and electrical connection (min. diam. 100 mm.).
• Fix 

SFERASOL

TM

 to the support foot through 4 wedges diam. 8 mm in the apposite 

holes on the base, ensuring that 3 mm. washers are 

fi

 tted with the wedges.

This operation avoids any condensate stagnancy inside the support foot. 
To this purpose, do not seal the support foot to the base with mortar or silicon.  

SFERASOL

TM

 e

  ciency can be further improved by following previous suggestions, 

thanks to its innovative shape, exploiting also the shaded part of the appliance. 

Exploiting di

 used energy, it is advisable to use light colors for any walls next to 

the appliance, and to create a 1,5 diam.white gravel circle in case of installation 
on lawn.    

The above advices enable a re

fl

 ection phenomenon of sunlight which optimizes 

the appliance e

  ciency.

INTEGRATED STORAGE COLLECTOR SFERASOL

TM

USE AND MAINTENANCE MANUAL

Содержание SFERASOL SF-A





















Отзывы: