sewerin EX-TEC PM 4 Скачать руководство пользователя страница 45

Страница: 45 / 98

3 Operation

Unit VOL%

Used to set individual measured

variables for the VOL range

(

Measuring VOL%

application).

VOL%
%VOL
%GAZ
%OBJ
tf.%

City Council
Frank Smith
Leakage Delivery

User name

Used to enter the user name.

This is important for document

ing the measurements.

The procedure and characters

that can be displayed are pro-

vided in the appendix.

Operator guidance

Used to select operator guidance

by application (House, Enclosed

spaces, Warning %LEL, Measur

ing VOL%) or by sensor (PPM,

LEL, VOL).
When using operator guidance

by sensor, the four applications

for measuring mode are replaced

by the following operating modes:

GAS DETECTION

(0..10000 PPM)

GAS WARNING

(0....100%LEL)

GAS MEASURING

(0....100 VOL%)

AUTOMATIC

Automatic measuring range

changeover from 0 ppm to 100 %

vol. according to gas concentra-

tion present.

Intended use
sensors

Содержание EX-TEC PM 4



































































































Результаты поиска

Содержание EX-TEC PM 4

Отзывы:

Похожие инструкции для EX-TEC PM 4

Бренды по названию

Популярные бренды

sewerin EX-TEC PM 4, Руководство по эксплуатации

Результаты поиска

Содержание EX-TEC PM 4

Отзывы:

Похожие инструкции для EX-TEC PM 4

Бренды по названию

Популярные бренды