FLOAT-TUBE
INFLATING
1.
Place your float-tube on a flat surface.
2.
Place the black cups around the base of these valves on the inner tubes.
3.
Slightly inflate the inner tubes to about 30% to start shaping them.
4.
Place each inner tube in each chamber of your float-tube, aligning the valves with the hole provided for this purpose.
5.
Close the 2 zippers.
6.
Close the main valve assembly (1) and open the valve caps (2).
7.
Using the pump and valve adapter, inflate the tubes evenly.
If the float-tube seems distorted at any point in the inflation process, stop and release the pressure. Then undo the zipper from the float-tube and adjust the
inner tube. When the adjustment is complete, slowly close the zipper and re-inflate the float-tube.
WARNING :
The air inside the float tube may expand if the air temperature and elevation change, which could cause the tube to burst. Never leave your float tube in
direct sunlight when it is out of the water. Always release some air when in these conditions. To deflate: Loosen the valve core assembly. (Turn to the left)
LIST OF COMPONENTS
If FOAM seat :
• 1 float-tube
• 2 side air chamber (one left and one right)
• 3 pieces of foam for seat and backrest
• 1 appron (with or withoyt PVC tube in 2pc, depend models)
• 1 pair of shoulder straps
• 1 repair bag
If INFLATE seat :
• 1 float-tube
• 2 side air chamber (one left and one right)
• 2 seat air chamber (one for seat and one for backrest)
• 1 appron (with or withoyt PVC tube in 2pc, depend models)
• 1 pair of shoulder straps
• 1 repair bag
«
APPRON
»
ASSEMBLY
1.
Fix the 2 straps of your apron on the left side of the float-tube by threading the strap through the buckle and “scratching” on the return.
2.
Once seated in your Float-tube, insert the right side of the belt straps.
Option: if your apron comes with a rigid frame, assemble the two pvc tubes together, and thread the whole on the front of your apron, the beveled side
down, then refer to point 1.
ASSEMBLY
!! WARNING !!
Always wear a local authorities approved life jacket.
Do Not overlook your physical limitations, as well as your equipment.
This instruction manual helps you with the initial assembly of your new SEVEN BASS float-tube, and provides basic safety instructions, reviews float-tube main-
tenance tips, and covers some simple repairs to perform. on the spot. Please review this documentation and familiarize yourself with the boat before using it.
If this is your first float tube, please consult your local dealer to make sure it is safe to use this craft.
• Take care when the wind and the current go from the shore / beach towards the open sea!
• Only use this float-tube in protected areas close to the shore / beach up to 300 m!
• Be careful that you have enough muscle strength to return to the starting point.
• Be careful that you do not reach a stony beach or a shoal because there is a risk of damaging the shell of the float-tube.
• Do not use the float-tube in the presence of winds with a force greater than 4 and / or waves with a height greater than 30 cm!
• If a storm begins, return immediately to calm water or to the beach!
• The use of this float-tube is prohibited for children not accompanied by an adult!
• We strongly recommend that you wear a life jacket at all times!
• The float-tube may capsize if you add too many loads!
• Do not make any modification to the float-tube that could jeopardize its safety and / or damage its structure!
• Do not leave your float-tube when it is damaged during use on the water. If an inner tube is missing, the float-tube still remains on the surface of the
water thanks to its considerable upward force. The multi-chamber system guarantees safe maneuverability.
• Never invert the float-tube to use its bottom as a diving board!
SEAT
ASSEMBLY
When foam seat :
3 pieces of foam :
- 1 piece for the backrest
- 2 piece for the seat
1.
place the longer foam piece in your folder in the backrest space provided for this purpose.
2.
then place the other 2 foam pieces in the location provided for the seat
3.
After assembling the backrest and seat, secure the seat cover flap by threading the strap
through the self-locking double bar buckle.
Repeat the procedure on the opposite side.
When Inflate seat :
2 air chambers of seats :
- 1 air chamber for the backrest (the smaller of the 2)
- 1 air chamber for the seat (the larger of the 2)
1.
place the inner tube of your backrest in the space provided for this purpose.
2.
then place the other air chamber in the location provided for the seat
3.
After assembling the backrest and the seat, secure the seat cover flap by threading the strap through the self-locking double bar buckle, or the zipper
if necessary, letting the valve come out in the middle
4.
Inflate both air chambers.
=
RIGHT air chanber
LEFT air chanber
BACK
FRONT
RIGHT
LEFT
1
2
AVERTISSEMENTS
ASSEMBLY INSTRUCTIONS AND USER MANUAL
FOR SEVEN BASS FLOAT-TUBE
Hard Fabric Line & PVC Line