Server Technology Switched Rack PDU страница 12 Скачать руководство пользователя | Manualshive

Страница: 12 / 157

background image

12



Installation Switched PDU

Installation and Operations Manual

NEBS GR-1089-Core Information

For NEBS certified products only.

These products are intended to be installed in Network Communications Facilities and in locations where the NEC applies.

This product is suitable for installation in a Common Bonding Network (CBN).

WARNING:

The intra-building port(s) of the equipment or subassembly is suitable for connection to intra-building or

unexposed wiring or cabling only. The intra-building port(s) of the equipment or subassembly MUST NOT be metallically
connected to interfaces that connect to the OSP or its wiring.

These interfaces are designed for use as intra-building interfaces only (Type 2 or Type 4 ports as described in
GR-1089-CORE, Issue 5) and require isolation from the exposed OSP cabling. The addition of Primary Protectors is not
sufficient protection in order to connect these interfaces metallically to OSP wiring.

«
...
10
11
12
13
14
...
»

Содержание Switched Rack PDU






























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Switched Rack PDU

Бренд: WattBox Страницы: 2

Бренд: Tripp Lite Страницы: 68

Бренд: Unipower Страницы: 13

Sureline DOV707H

Бренд: Safeline Страницы: 32

Бренд: Sharp Страницы: 27

Бренд: Sharp Страницы: 39

Бренд: Panamax Страницы: 2

Бренд: Vertiv Страницы: 12

Бренд: Rittal Страницы: 22

Бренд: Rittal Страницы: 77

Schroff 23147 - 005

Бренд: Pentair Страницы: 8

Бренд: OBO Bettermann Страницы: 75

Pacesetter 2995

Бренд: Bodine Страницы: 20

Бренд: Torus Power Страницы: 12

Metered Rack PDU

Бренд: Tripp Lite Страницы: 4

Бренд: Tripp Lite Страницы: 12

AGIB6098 Series

Бренд: Tripp Lite Страницы: 16

Бренд: StarTech.com Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды