SEPTENTRIO mosaic Series Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 57

background image

46

46

Evaluation Kit: mosaic-go

46

8

Evaluation Kit: mosaic-go

The mosaic-go Evaluation Kit is composed of the mosaic module soldered on an interface
board inside a metallic housing.

Mosaic-go part number:

Single-antenna version, incorporating mosaic-X5:

410386

(including accessories).

Dual-antenna version, incorporating mosaic-H:

410397

(including accessories).

Dimensions: 71 x 59 x 12 mm ± 1 mm
Weight:

58 g ± 1 g

8.1

Interfaces

8.1.1

USB

This micro-B connector is used to access the mosaic-go over USB.

It can also be used to power the mosaic-go. See also section 8.4.

8.1.2

RSV USB

This connector is reserved and should not be used.

8.1.3

RF_IN1 and RF_IN2

These are the main and auxiliary antenna connectors, connected to the ANT_1 and ANT_2
pins of the internal mosaic. See section 4.2 for details.

«
...
44
45
46
47
48
...
»

Содержание mosaic Series


























































Отзывы:

Нет отзывов

Похожие инструкции для mosaic Series

Бренд: Camozzi Страницы: 33

Бренд: Camozzi Страницы: 2

Бренд: Camozzi Страницы: 64

Бренд: dbx Страницы: 52

Бренд: Hankscraft Runxin Страницы: 58

Бренд: Tylo Страницы: 51

Бренд: Daruifuno Страницы: 24

Бренд: Reliance Foundry Страницы: 3

Бренд: Wesa Страницы: 8

Бренд: hotset Страницы: 2

Бренд: Blue Point Engineering Страницы: 12

Бренд: DMP Electronics Страницы: 56

Бренд: REMKO Страницы: 20

Ramping and Profiling Microprocessor-Based Control SERIES 1500

Бренд: Watlow Страницы: 90

Бренд: Maco Страницы: 40

Бренд: QSC Страницы: 13

Бренд: GAC Страницы: 4

Бренд: Omron Страницы: 510

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды