SEPTENTRIO AsteRx-U3 Скачать руководство пользователя страница 42

Страница: 42 / 83

4.1. HOW TO CONFIGURE THE ASTERX-U3 FOR RTK

4.1.3 How to con

ﬁ

gure the AsteRx-U3 in RTK rover

mode using TCP/IP in a closed network

Step 1: Con

ﬁ

gure the Base station receiver

Set the Base station position as static

Section 5.1 describes how to con

ﬁ

gure the AsteRx-U3 as an RTK base station.

Conﬁgure the Ethernet connection and diﬀ corr output from the Base
station receiver

In the

Corrections Output

window click on

New RTCM3 output

to start the sequence

of steps to con

ﬁ

gure the RTK diﬀerential corrections stream and Ethernet connection over

which the diﬀ corr will be sent. In the example shown in Figure 4-10, RTCMv3 correction
data are sent out over port 28785. The RTCMv3 messages necessary for RTK positioning are
selected by default.

Содержание AsteRx-U3




















































































Результаты поиска

Содержание AsteRx-U3

Отзывы:

Похожие инструкции для AsteRx-U3

Бренды по названию

Популярные бренды

SEPTENTRIO AsteRx-U3, Руководство пользователя

Результаты поиска

Содержание AsteRx-U3

Отзывы:

Похожие инструкции для AsteRx-U3

Бренды по названию

Популярные бренды